Faculty of Engineering

Electrical / Medical Science (2017)


Note: This course version applies only to students first enrolling in 2017.
WARNING: This course version is currently under review and is subject to change.


1. Overview

Course: Electrical / Medical Science (2017)
CP Required: 240
Min FT Duration: 5.00 Years
Min PT Duration: 5.00 Years
Faculty/School: Faculty of Engineering
Years Offered: 2017, 2016, 2015

2. Requirements

In summary the requirements are:

Students must complete 240 credit points as follows:

Engineering (144 credit points):

► 36 credit points of Engineering core units

► 78 credit points of Electrical stream core units

► 30 credit points of Electrical Specialist elective units

Medical Science:

► 96 credit points of Medical Science units

The handbook rules governing this degree are as follows:

To qualify for the award of the combined degree:

(a) For all Bachelor of Engineering combined degrees a candidate must complete 240 credit points and satisfy any additional requirements specified.

(b) Where the requirements specified in the following clauses account for less than the total required credit, candidates must complete additional units of study (not including general electives) from the relevant Bachelor of Engineering Honours specialist stream table subject to any conditions specified in that table as may be necessary to satisfy the requirements of the degree.

Requirements for the Bachelor of Engineering

For the Bachelor of Engineering component of a combined degree:

(a) The units of study that may be taken for the Bachelor of Engineering component of the combined degree are set out in the tables of units of study for the Bachelor of Engineering single degree;

(b) Except where varied by other clauses in the course resolutions, all candidates must complete a minimum of 144 credit points comprising:

(i) 36cp from the Engineering Core Table, including all required units;

(ii) 108cp from the Engineering Stream Core Table pertaining to the specialist stream being undertaken, including all required units;

(c) The Faculty Board may approve, based on appropriate academic justification, a list of approved unit alternatives. These alternatives specify, for particular Engineering stream / combined degree combinations, units within the normal requirements for the Bachelor of Engineering component of the combined degree that can be replaced by specified alternative units that would form part of the normal program for single degree students in that stream.

Requirements for the Bachelor of Medical Science

For the Bachelor of Medical Science component of a combined degree:

(a) The units of study that may be taken are listed in Table IV for the Bachelor of Medical Science from the Faculty of Science.

(b) The mathematics requirement for the Bachelor of Engineering component of the combined degree will also satisfy the mathematics requirements for the Bachelor of Medical Science component.

(c) Candidates must complete 96 credit points of units including:

(i) A minimum of 24 credit points from junior Science units of study, including:

- 12 credit points from Chemistry; and

- 12 credit points from BIOL1XXX

(ii) 48 credit points from intermediate Science units of study, comprising:

- 36 credit points of BMED240# units from Table IV (B) for the Bachelor of Medical Science; and

- MBLG2071/2971 Molecular Biology and Genomics; and

- MBLG2072/2972 Genetics and Genomics.

Note: changes to the Medical Science degree from 2019 require that alternative units replace some core Med Sci units.

- In place of the 36 cp of BMED240X units, take MEDS2001, MEDS2002, MEDS2003, MEDS2004 and MEDS2005 and one additional medical science elective.

- In place of MBLG2X71 and MBLG2X72 take GEGE2001 and BCMB2002.

(iii) A minimum of 24 credit points of senior Science units of study selected from the Bachelor of Science (Medical Science) Table.

Optional Science Major

The completion of a Science major through selection of appropriate Senior Science units is possible as part of the Engineering/Medical Science combined degree, but not required. Any student who satisfies the requirements of a Science major through the Science units taken as part of the combined degree shall have that major recorded on the Bachelor of Medical Science testamur at the completion of the degree.

The majors available in medical science discipline areas are Anatomy and Histology*, Applied Medical Science (Transitional Provision), Biochemistry*, Cell Pathology, Immunobiology*, Microbiology*, Molecular Biology and Genetics*, Neuroscience*, Nutrition and Metabolism, Pharmacology*, Physiology*

* indicates a major in this area is also available at the advanced level

The requirements for completion of the above majors is set out in Table I of the Handbook http://sydney.edu.au/handbooks/science/table1/table1_overview.shtml

Medical Science Honours

Honours in Medical Science requires the completion of one additional full time year of study. Admission and award requirements for Honours in the Bachelor of Medical Science are listed in the resolutions of the Faculty of Science.

To qualify for the award of the Honours degree, a student must complete 48 credit points of Honours units of study in one of the Honours subjects listed in the Bachelor of Medical Science Table IV (D).

Candidates for the award of the Bachelor of Medical Science (Honours) who do not meet the requirements, and who have not already graduated, will be awarded the Bachelor of Medical Science pass degree.

Engineering Honours Requirements

(a) an EWAM of at least 65 immediately prior to the semester in which a thesis unit of study is first attempted; and

(b) have an EIHWAM of at least 65 at the completion of the degree; and

(c) complete the requirements within a time limit of 5 years for a single Bachelor of Engineering Honours degree or complete the requirements within a time limit of 6 years for a combined Bachelor of Engineering Honours combined degree.

Candidates who satisfy the requirements for the Engineering degree, but who have not satisfied each of Clauses (a), (b) and (c), will qualify for the award of the Bachelor of Engineering degree (i.e. the PASS degree, awarded without Honours).

Advanced units in Maths and Science

Most units of study offered by the Science Faculty on the list of core requirements can be replaced by an equivalent advanced level unit, subject to prerequisite conditions (as required by the Faculty of Science) being met. Students considering doing advanced options should seek advice from their department before enrolling.

Majors

A major requires:

(a) the completion of 24 credit points chosen from units of study listed in the table for that major;

(b) satisfying any additional requirements specified for the major, and listed with the table of units for the major;

(c) the completion of a thesis project that has been approved by the Head of School (or delegate) as relevant to the topic of the major.

Study Abroad

Students undertaking Study Abroad in a particular year of their degree must enrol in the appropriate International Exchange Program units of study as an alternative to a semester`s standard units.

Permission from the relevant Head of School must be sought prior to enrolling in exchange units of study.

Faculty Resolutions

Details of relevant Faculty resolutions are available via the university handbook site at: http://sydney.edu.au/handbooks/

3. Semesters

Year 1 - Semester 1

Type CP CP From
6 Select from CHEM1101: Chemistry 1A


Note: This unit is discontinued from 2018. Replacement unit is CHEM1111.
3 Select from MATH1001: Differential Calculus


Note: This unit is discontinued from 2018. Replacement unit is MATH1021.
6 Select from INFO1103: Introduction to Programming


Note: This unit is discontinued from 2018. Replacement unit is INFO1113.
6 Select from ENGG1111: Integrated Engineering 1
3 Select from MATH1002: Linear Algebra

Note: ENGG1111 may be replaced by ENGG1061 Advanced Engineering for approved students. MATH1001 and MATH1002 may be replaced by advanced units MATH1901 and MATH1902.

Year 1 - Semester 2

Type CP CP From
6 Select from INFO1105: Data Structures


Note: This unit is discontinued from 2018. Replacement unit is COMP2123.
3 Select from MATH1003: Integral Calculus and Modelling


Note: This unit is discontinued from 2018. Replacement unit is MATH1023.
3 Select from MATH1005: Statistical Thinking with Data
6 Select from ELEC1601: Introduction to Computer Systems
6 Select from CHEM1102: Chemistry 1B

Note: MATH1003 and MATH1005 may be replaced by advanced units MATH1903 and MATH1905.

Year 2 - Semester 1

Type CP CP From
6 Select from BIOL1003: Human Biology
BIOL1006: Life and Evolution
6 Select from ELEC1103: Fundamentals of Electrical and Electronic Engineering
6 Select from PHYS1001: Physics 1 (Regular)
6 Select from MATH2061: Linear Mathematics and Vector Calculus

Year 2 - Semester 2

Type CP CP From
2 Select from ENGG2111: Integrated Engineering 2
6 Select from BIOL1007: From Molecules to Ecosystems
6 Select from PHYS1003: Physics 1 (Technological)
6 Select from ELEC2103: Simulation and Numerical Solutions in Engineering
6 Select from ELEC2104: Electronic Devices and Circuits

Note: ENGG2111 may be replaced by ENGG2062 Engineering Project: Business Plan 2 Adv, with Faculty approval.

Year 3 - Semester 1

Type CP CP From
6 Select from COMP2129: Operating Systems and Machine Principles


Note: This unit is discontinued from 2018. Replacement unit is COMP2017.
6 Select from ELEC2602: Digital Logic
6 Select from BMED2402: Nerve and Muscle
6 Select from BMED2401: Cellular Foundations of Medical Sciences

Note: Alternative units replace some core Med Sci units from 2019. Please contact a Medical Science adviser if you have any questions regarding unit selection.

Year 3 - Semester 2

Type CP CP From
6 Select from BMED2405: Gut and nutrient metabolism
6 Select from PHYS2213: Physics 2EE
6 Select from ELEC2302: Signals and Systems
6 Select from BMED2404: Microbes, Infection and Immunity

Note: Alternative units replace some core Med Sci units from 2019. Please contact a Medical Science adviser if you have any questions regarding unit selection.

Year 4 - Semester 1

Type CP CP From
6 Select from MBLG2071: Molecular Biology and Genomics


Note: This unit is discontinued from 2018. Replacement unit is BCMB2002 (offered in Semester 2).

BCMB2002 may be substituted for the advanced alternative BCMB2902.
2 Select from ENGG3111: Integrated Engineering 3
6 Select from Unit Block:
Electrical Specialist - Electives
6 Select from Unit Block:
Electrical Specialist - Electives
6 Select from BMED2403: Cardiovascular & Respiratory Systems

Note: ENGG3111 may be replaced by ENGG3062 Technology Education (Adv), with Faculty approval.

Alternative units replace some core Med Sci units from 2019. Please contact a Medical Science adviser if you have any questions regarding unit selection.

Year 4 - Semester 2

Type CP CP From
6 Select from MBLG2072: Genetics and Genomics


Note: This unit is discontinued from 2018. Replacement unit is GEGE2001 (offered in Semester 1).

GEGE2001 may be substituted for the advanced alternative GEGE2901.
6 Select from BMED2406: Hormones, Kidney and Reproduction
6 Select from Unit Block:
Electrical Specialist - Electives
6 Select from Unit Block:
Electrical Specialist - Electives

Note: Alternative units replace some core Med Sci units from 2019. Please contact a Medical Science adviser if you have any questions regarding unit selection.

Year 5 - Semester 1

Type CP CP From
6 Select from ELEC4712: Thesis A
2 Select from ENGG4111: Integrated Engineering 4
6 Select from Unit Block:
Medical Science Senior Electives
6 Select from Unit Block:
Medical Science Senior Electives
0 Select from ENGG4000: Practical Experience
6 Select from Unit Block:
Electrical Specialist - Electives

Note: The Medical Science degree requires a minimum of 24 credit points from senior Science units of study.

ENGG4111 may be replaced by ENGG4064/4065 Advanced Engineering Design A/B, with Faculty approval.

Year 5 - Semester 2

Type CP CP From
6 Select from Unit Block:
Medical Science Senior Electives
6 Select from Unit Block:
Medical Science Senior Electives
6 Select from ELEC4713: Thesis B

Note: The Medical Science degree requires a minimum of 24 credit points from senior Science units of study.

4. Pathways

48cp Majors

Type CP CP From

Note: From 2019 onwards, all engineering majors will be converted to the 48 credit point format, and several new majors will be introduced - details can be viewed in the 2019 degree structures.

You can find more information at https://canvas.sydney.edu.au/courses/2806/pages/feit-your-studies-bachelor-of-engineering-majors

Major in Computer Engineering (24cp)

Type CP CP From
Core
6 ELEC3506: Communications Networks
Core
6 ELEC3607: Embedded Systems
Core
6 ELEC3608: Computer Architecture
List
6 Select from COMP3520: Operating Systems Internals
ELEC3104: Engineering Electromagnetics
ELEC3304: Control
ELEC3305: Digital Signal Processing
ELEC3404: Electronic Circuit Design
ELEC3702: Management for Engineers

Note: 24 Credit Points to Complete this Major

Please check the prerequisites for the higher level units in this major and ensure you will be able to complete them prior to undertaking the higher level units.

Major in Internet of Things (IoT) (24cp)

Type CP CP From
Core
6 ELEC5514: Networked Embedded Systems
Core
6 ELEC5517: Software Defined Networks
Elective
12 Electives.

Note: Select 12 credit points from: ELEC5518, ELEC5616, ELEC5208, ELEC5508, INFO3406, COMP5047, COMP5216, COMP5426

Major in Power Engineering (24cp)

Type CP CP From
Core
6 ELEC3203: Electricity Networks
Core
6 ELEC3204: Power Electronics and Applications
Core
6 ELEC3206: Electrical Energy Conversion Systems
Core
6 ELEC3304: Control
Core
6 ELEC5204: Power Systems Analysis and Protection
6 Select from ELEC5205: High Voltage Engineering [not offered in 2021]
ELEC5211: Power System Dynamics and Control
ELEC5212: Power System Planning and Markets

Note: 36 CP minimum Requirements to achieve this Major.

-ELEC3203 and ELEC3206 are not counted towards the major, but are pre-requisites for the ELEC5204 units.

Please check the prerequisites for the higher level units in this major and ensure you will be able to complete them prior to undertaking the higher level units.

Major in Telecommunications Engineering (24cp)

Type CP CP From
Core
6 ELEC3305: Digital Signal Processing
Core
6 ELEC3405: Communications Electronics and Photonics
Core
6 ELEC3505: Communications
Core
6 ELEC3506: Communications Networks
Core
6 ELEC4505: Digital Communication Systems

Note: All units must be completed (30 Credit Points).

Please check the prerequisites for the higher level units in this major and ensure you will be able to complete them prior to undertaking the higher level units.

5. Unit Blocks

Block 1 - Engineering Core (Min CP: 36,Max CP: 36)

Unit Code Unit Name CP Sessions Offered
AERO2711 Aerospace Engineering Project 1 6 Semester 1
Semester 2
Int February
Int July
AERO3711 Aerospace Engineering Project 2 6 Semester 1
Semester 2
Int February
Int July
AERO4711 Aerospace Engineering Project 3 6 Semester 1
Semester 2
Int February
Int July
AMME4010 Major Industrial Project 24 Semester 1
Semester 2
AMME4111 Thesis A 6 Semester 1
Semester 2
AMME4112 Thesis B 6 Semester 1
Semester 2
CHNG4203 Major Industrial Project 24 Semester 1
Semester 2
CHNG4811 Thesis A 6 Semester 1
Semester 2
CHNG4812 Thesis B 6 Semester 1
Semester 2
CIVL4022 Thesis A 6 Semester 1
Semester 2
CIVL4023 Thesis B 6 Semester 1
Semester 2
ELEC4702 Practical Experience 0 Int February
Int March
Int April
Int May
Int June
Int July
Int August
Int September
Int October
Int November
Int December
ELEC4712 Thesis A 6 Semester 1
Semester 2
ELEC4713 Thesis B 6 Semester 1
Semester 2
ELEC4714 Major Industrial Project 24 Semester 1
Semester 2
ENGG1061 Advanced Engineering 1 6 Semester 1
Semester 2
ENGG1111 Integrated Engineering 1 6 Semester 1
ENGG2062 Engineering Project: Business Plan 2 Adv 6 Semester 2
ENGG2111 Integrated Engineering 2 2 Semester 1
Semester 2
Int February
ENGG3062 Technology Education (Advanced) 6 Semester 2
ENGG3111 Integrated Engineering 3 2 Semester 1
Semester 2
ENGG4000 Practical Experience 0 Int January
Int February
Int March
Int April
Int May
Int June
Int July
Int August
Int September
Int October
Int November
Int December
ENGG4064 Advanced Engineering Design A 6 Semester 2
Int July
ENGG4065 Advanced Engineering Design B 6 Semester 2
ENGG4111 Integrated Engineering 4 2 Semester 1
MATH1001 Differential Calculus 3 Semester 1
Summer Main
MATH1002 Linear Algebra 3 Semester 1
Semester 2
Summer Main
MATH1003 Integral Calculus and Modelling 3 Semester 2
Summer Main
MATH1005 Statistical Thinking with Data 3 Semester 1
Semester 2
Int January
MATH1901 Differential Calculus (Advanced) 3 Semester 1
MATH1902 Linear Algebra (Advanced) 3 Semester 1
MATH1903 Integral Calculus and Modelling Advanced 3 Semester 2
MATH1905 Statistics (Advanced) 3 Semester 2

Note: Complete a minimum of 36cp including:

- ENGG4000 Practical Experience (0cp) or ELEC4702 Practical Experience (0cp)

- Exactly 6cp from ENGG1111 Integrated Engineering 1 (6cp) OR ENGG1061 Advanced Engineering 1A (6cp) (see note 1)

- At least 2cp from ENGG2xxx Integrated Engineering 2 (2cp) OR ENGG2062 Engineering Project Business Plan 2 Adv (6cp) (see note 1) OR AERO2711 Aerospace Engineering Project 1 (see note 1)

- At least 2cp from ENGG3xxx Integrated Engineering 3 (2cp) OR ENGG3062 Technology Education (Advanced) (6cp) (see note 1) OR AERO3711 Advanced Aerospace Project 2 (see note 1)

- At least 2cp from ENGG4xxx Integrated Engineering 4 (2cp) OR ENGG4064 Advanced Engineering Design A (6cp) (see note 1) OR ENGG4065 Advanced Engineering Design B (6cp) (see note 1) OR AERO4711 Advanced Aerospace Project 3 (see note 1)

- Exactly 12cp of MATH1xxxx units: MATH1001 Differential Calculus (3cp) AND MATH1002 Linear Algebra (3cp) AND MATH1003 Integral Calculus AND Modelling (3cp) MATH1005 Statistics (3cp)

- A minimum of 12cp of (see notes 2,3) from either AMME4111-4112 Thesis A & B (6cp+6cp) OR CHNG4811-CHNG4812 hesis A & B (6cp+6cp) OR CIVL4022-4023 Thesis A & B (6cp+6cp) OR ELEC4712-4713 Thesis A & B (6cp+6cp) OR AMME4010 Major Industrial Project (24cp) OR CHNG4203 Major Industrial Project (24cp) OR ELEC4714 Major Industrial Project (24cp)

Note 1. The Advanced Engineering units are only available to students who have been accepted into the relevant year of the Advanced Engineering program.

Note 2. All Thesis A units are mutually prohibited (meaning that only one can be completed), and all Thesis B units have the associated Thesis A unit as a pre-requisite. Students may undertake only the Thesis units relevant to their stream.

Block 2 - Electrical Core (Min CP: 78,Max CP: 78)

Unit Code Unit Name CP Sessions Offered
COMP2129 Operating Systems and Machine Principles 6 Semester 1
ELEC1103 Fundamentals of Electrical and Electronic Engineering 6 Semester 1
ELEC1601 Introduction to Computer Systems 6 Semester 2
ELEC2103 Simulation and Numerical Solutions in Engineering 6 Semester 2
ELEC2104 Electronic Devices and Circuits 6 Semester 2
ELEC2302 Signals and Systems 6 Semester 2
ELEC2602 Digital Logic 6 Semester 1
INFO1103 Introduction to Programming 6 Semester 1
Semester 2
INFO1105 Data Structures 6 Semester 2
Summer Early
Summer Main
MATH2061 Linear Mathematics and Vector Calculus 6 Semester 1
Summer Main
PHYS1001 Physics 1 (Regular) 6 Semester 1
PHYS1003 Physics 1 (Technological) 6 Semester 2
PHYS2213 Physics 2EE 6 Semester 2

Block 3 - Electrical Specialist - Electives (Min CP: 30,Max CP: 30)

Unit Code Unit Name CP Sessions Offered
ELEC3104 Engineering Electromagnetics 6 Semester 1
ELEC3203 Electricity Networks 6 Semester 1
ELEC3204 Power Electronics and Applications 6 Semester 1
ELEC3206 Electrical Energy Conversion Systems 6 Semester 2
ELEC3304 Control 6 Semester 2
ELEC3305 Digital Signal Processing 6 Semester 1
ELEC3404 Electronic Circuit Design 6 Semester 1
ELEC3405 Communications Electronics and Photonics 6 Semester 2
ELEC3505 Communications 6 Semester 1
ELEC3506 Communications Networks 6 Semester 2
ELEC3607 Embedded Systems 6 Semester 1
ELEC3608 Computer Architecture 6 Semester 2
ELEC3609 Internet Software Platforms 6 Semester 2
ELEC3610 E-Business Analysis and Design 6 Semester 1
ELEC3702 Management for Engineers 6 Semester 2
ELEC3802 Fundamentals of Biomedical Engineering 6 Semester 1
ELEC3803 Bioelectronics [not offered in 2021] 6 Semester 2
ELEC4505 Digital Communication Systems 6 Semester 1
ELEC4706 Project Management 6 Semester 1
ELEC5101 Antennas and Propagation 6 Semester 2
ELEC5203 Topics in Power Engineering [not offered in 2021] 6 Semester 2
ELEC5204 Power Systems Analysis and Protection 6 Semester 1
ELEC5205 High Voltage Engineering [not offered in 2021] 6 Semester 2
ELEC5206 Sustainable Energy Systems 6 Semester 2
ELEC5207 Advanced Power Conversion Technologies 6 Semester 2
ELEC5208 Intelligent Electricity Networks 6 Semester 1
ELEC5211 Power System Dynamics and Control 6 Semester 1
ELEC5212 Power System Planning and Markets 6 Semester 2
ELEC5303 Computer Control System Design [not Offered 2021] 6 Semester 1
ELEC5304 Intelligent Visual Signal Understanding 6 Semester 1
ELEC5305 Acoustics, Speech and Signal Processing 6 Semester 2
ELEC5306 Video Intelligence and Compression 6 Semester 1
ELEC5307 Advanced Signal Processing with Deep Learning 6 Semester 2
ELEC5402 Digital Integrated Circuit Design 6
ELEC5403 Radio Frequency Engineering [not offered in 2021] 6 Semester 1
ELEC5507 Error Control Coding 6 Semester 1
ELEC5508 Wireless Engineering 6 Semester 2
ELEC5509 Mobile Networks 6 Semester 1
ELEC5510 Satellite Communication Systems 6 Semester 2
ELEC5511 Optical Communication Systems 6 Semester 1
ELEC5512 Optical Networks 6 Semester 2
ELEC5514 Networked Embedded Systems 6 Semester 2
ELEC5516 Electrical and Optical Sensor Design 6 Semester 1
ELEC5614 Real Time Computing 6 Semester 1
ELEC5615 Advanced Computer Architecture 6 Semester 1
ELEC5616 Computer and Network Security 6 Semester 1
ELEC5617 Topics in Software Engineering 6 Semester 2
ELEC5618 Software Quality Engineering 6 Semester 1
ELEC5619 Object Oriented Application Frameworks 6 Semester 2
ELEC5620 Model Based Software Engineering 6 Semester 2
ELEC5621 Digital Systems Design 6
ELEC5622 Signals, Software and Health 6 Semester 2
ELEC5701 Technology Venture Creation [not offered in 2021] 6 Semester 2
ELEC5803 Advanced Bioelectronics [Not Offered 2019] 6 Semester 1

Note: A minimum of 30 credit points (five units of study) must be taken. Specialist units include all ELEC3xxx, ELEC4xxx and ELEC5xxx units of study.

Block 4 - Engineering General Electives

Unit Code Unit Name CP Sessions Offered
COMP3520 Operating Systems Internals 6 Semester 2

Note: The following units are approved as general electives for Bachelor of Engineering Honours Students, provided that students are able to meet the enrolment requirements specified by the relevant faculty and provided that the unit of study is not substantially the same as a unit of study already completed.

(1) All units offered by the following Faculties: Engineering and Information Technologies, Business, Science, Arts and Social Sciences.

(2) Additional units as included in the list of approved general Engineering electives, as approved by the Faculty Board (or, within delegated authority, the Faculty Courses Committee).

Block 5 - Medical Science Core (Min CP: 72,Max CP: 72)

Unit Code Unit Name CP Sessions Offered
BIOL1001 Concepts in Biology 6 Semester 1
BIOL1002 Living Systems 6 Semester 2
BIOL1003 Human Biology 6 Semester 1
BIOL1006 Life and Evolution 6 Semester 1
BIOL1007 From Molecules to Ecosystems 6 Semester 2
BIOL1902 Living Systems (Advanced) 6 Semester 2
BIOL1903 Human Biology (Advanced) 6 Semester 1
BMED2401 Cellular Foundations of Medical Sciences 6 Semester 1
BMED2402 Nerve and Muscle 6 Semester 1
BMED2403 Cardiovascular & Respiratory Systems 6 Semester 1
BMED2404 Microbes, Infection and Immunity 6 Semester 2
BMED2405 Gut and nutrient metabolism 6 Semester 2
BMED2406 Hormones, Kidney and Reproduction 6 Semester 2
CHEM1101 Chemistry 1A 6 Semester 1
Semester 2
Summer Main
CHEM1102 Chemistry 1B 6 Semester 1
Semester 2
Summer Main
MBLG1001 Molecular Biology and Genetics (Intro) 6 Semester 2
MBLG1901 Molecular Biology and Genetics (Adv) 6 Semester 2
MBLG2071 Molecular Biology and Genomics 6 Semester 1
MBLG2072 Genetics and Genomics 6 Semester 2
MBLG2971 Molecular Biology and Genomics (Adv) 6 Semester 1
MBLG2972 Genetics and Genomics (Adv) 6 Semester 2

Note: CHEM1101, CHEM1102, BIOL1007, MBLG2071, MBLG2072 and all BMED240# must be taken.

At least 6 Credit points of BIOL1#0# must be taken.

Advanced Science units (listed here) may be taken in place of the standard units, i.e. BIOL1903, BIOL1906, BIOL1907, CHEM1901, CHEM1902, MBLG2971, MBLG2972.

Block 6 - Medical Science Senior Electives (Min CP: 24,Max CP: 24)

Note: Candidates are required to complete 24 credit points of Senior units of study from the subject areas of: Anatomy, Applied Medical Science, Biology (Genetics) (i.e. BIOL3018/3918, BIOL3026/3926), Biochemistry, Cell Pathology, Histology, Immunology, Infectious Diseases, Microbiology, Neuroscience, Nutrition and Metabolism, Pharmacology, Physiology, Virology.

Of these, the majors available in medical science discipline areas are:

► Anatomy and Histology*

► Applied Medical Science (Transitional Provision)

► Biochemistry*

► Cell Pathology

► Immunobiology*

► Microbiology*

► Molecular Biology and Genetics*

► Neuroscience*

► Nutrition and Metabolism

► Pharmacology*

► Physiology*

* indicates a major in this area is also available at the advanced level

The requirements for completion of the above majors is set out in Table I of the Handbook http://sydney.edu.au/handbooks/science/table1/table1_overview.shtml