Faculty of Engineering

Mechatronic / Project Management (2017)


Note: This course version applies only to students first enrolling in 2017.
WARNING: This course version is currently under review and is subject to change.


1. Overview

Course: Mechatronic / Project Management (2017)
CP Required: 240
Min FT Duration: 5.00 Years
Min PT Duration: N/A
Faculty/School: Faculty of Engineering
Years Offered: 2018, 2017, 2016, 2015

2. Requirements

In summary the requirements are:

Students must complete 240 credit points as follows:

Engineering (156 credit points):

► 36 credit points of Engineering core units

► 108 credit points of Mechatronic stream core units

► 12 credit points of Mechatronic Specialist elective units

Project Management:

► 66 credit points of Project Management core units

► 18 credit points of Project Management elective units

The handbook rules governing this degree are as follows:

To qualify for the award of the combined degree:

(a) For all Bachelor of Engineering combined degrees a candidate must complete 240 credit points and satisfy any additional requirements specified.

(b) Where the requirements specified in the following clauses account for less than the total required credit, candidates must complete additional units of study from the tables relevant to the Bachelor of Engineering as may be necessary to satisfy the requirements of the degree.

Requirements for the Bachelor of Engineering

For the Bachelor of Engineering component of a combined degree:

(a) The units of study that may be taken for the Bachelor of Engineering component of the combined degree are set out in the tables of units of study for the Bachelor of Engineering single degree;

(b) Except where approved, all candidates must complete a minimum of 144 credit points comprising:

(i) 36cp from the Engineering Core Table, including all required units;

(ii) 108cp from the Engineering Stream Core Table pertaining to the specialist stream being undertaken, including all required units;

(c) The Faculty Board may approve, based on appropriate academic justification, a list of approved unit alternatives. These alternatives specify, for particular Engineering stream / combined degree combinations, units within the normal requirements for the Bachelor of Engineering component of the combined degree that can be replaced by specified alternative units that would form part of the normal program for single degree students in that stream.

Candidates who do not meet the requirements for the award of the Bachelor of Engineering Honours but who have otherwise satisfied the requirements of the Bachelor of Engineering shall graduate with the Bachelor of Engineering pass degree.

Requirements for the Bachelor of Project Management

For the Bachelor of Project Management component of a combined degree:

(a) Candidates must complete the core units of study as set out in the Bachelor of Project Management Unit of Study Table.

(b) 18cp from the Project Management Electives Table must be completed.

Engineering Honours Requirements

(a) an EWAM of at least 65 immediately prior to the semester in which a thesis unit of study is first attempted; and

(b) have an EIHWAM of at least 65 at the completion of the degree; and

(c) complete the requirements within a time limit of 5 years for a single Bachelor of Engineering Honours degree or complete the requirements within a time limit of 6 years for a combined Bachelor of Engineering Honours combined degree.

Candidates who satisfy the requirements for the Engineering degree, but who have not satisfied each of Clauses (a), (b) and (c), will qualify for the award of the Bachelor of Engineering degree (i.e. the PASS degree, awarded without Honours).

Advanced units in Maths and Science

Most units of study offered by the Science Faculty on the list of core requirements can be replaced by an equivalent advanced level unit; subject to prerequisite conditions (as required by the Faculty of Science) being met. Students considering doing advanced options should seek advice from their department before enrolling.

Majors

A major requires:

(a) the completion of 24 credit points chosen from units of study listed in the table for that major;

(b) satisfying any additional requirements specified for the major, and listed with the table of units for the major;

(c) the completion of a thesis project that has been approved by the Head of School (or delegate) as relevant to the topic of the major.

Study Abroad

Students undertaking Study Abroad in a particular year of their degree must enrol in the appropriate International Exchange Program units of study as an alternative to a semester`s standard units.

Permission from the relevant Head of School must be sought prior to enrolling in exchange units of study.

Faculty Resolutions

Details of relevant Faculty resolutions are available via the university handbook site at: http://sydney.edu.au/handbooks/

3. Semesters

Year 1 - Semester 1

Type CP CP From
3 Select from MATH1001: Differential Calculus


Note: This unit is discontinued from 2018. Replacement unit is MATH1021.
6 Select from ENGG1801: Engineering Computing
6 Select from ENGG1850: Introduction to Project Management
3 Select from MATH1002: Linear Algebra
6 Select from MTRX1701: Introduction to Mechatronic Engineering

Note: MATH1001 and MATH1002 may be replaced by advanced units MATH1901 and MATH1902.

Year 1 - Semester 2

Type CP CP From
3 Select from MATH1003: Integral Calculus and Modelling


Note: This unit is discontinued from 2018. Replacement unit is MATH1023.
6 Select from PMGT1852: Facilitation and Stakeholder Engagement
6 Select from AMME1362: Materials 1
6 Select from ENGG1802: Engineering Mechanics
3 Select from MATH1005: Statistics

Note: MATH1003 and MATH1005 may be replaced by advanced units MATH1903 and MATH1905.

Year 2 - Semester 1

Type CP CP From
6 Select from ENGG1111: Integrated Engineering 1
6 Select from BUSS1040: Economics for Business Decision Making
6 Select from ELEC1103: Fundamentals of Electrical and Electronic Engineering
6 Select from AMME2500: Engineering Dynamics

Note: ENGG1111 may be replaced by ENGG1061 Advanced Engineering for approved students.

Students in the Space major do not undertake Integrated Engineering units and should substitute a unit from their major.

Year 2 - Semester 2

Type CP CP From
6 Select from MTRX1705: Introduction to Mechatronic Design
6 Select from MTRX1702: Mechatronics 1
6 Select from ENGG2855: Project Acceptance
6 Select from ENGG2852: Project Based Organisational Behaviour


Note: This unit is discontinued from 2019. Replacement unit is PMGT2854.

Year 3 - Semester 1

Type CP CP From
6 Select from ENGG2850: Project Cost and Finance
6 Select from ENGG2851: Project Analytics
6 Select from MTRX2700: Mechatronics 2
6 Select from AMME3500: System Dynamics and Control

Year 3 - Semester 2

Type CP CP From
2 Select from ENGG2111: Integrated Engineering 2
6 Select from MECH2400: Mechanical Design 1
6 Select from ENGG3854: Legal Aspects of Projects
6 Select from AMME2301: Mechanics of Solids 1
6 Select from ELEC2104: Electronic Devices and Circuits

Note: ENGG2111 may be replaced by ENGG2062 Engineering Project: Business Plan 2 Adv, with Faculty approval.

Students in the Space major do not undertake Integrated Engineering units and should substitute a unit from their major.

Year 4 - Semester 1

Type CP CP From
2 Select from ENGG3111: Integrated Engineering 3
6 Select from ENGG3853: Project Risk Management: Tools & Techniques
6 Select from MECH3660: Manufacturing Engineering
6 Select from PMGT3858: Adapting to Project Context
6 Select from Unit Block:
Project Management Electives


Note: At least 18 credit points of Project Management elective units must be completed. These may be taken in either semester.

Note: ENGG3111 may be replaced by ENGG3062 Technology Education (Adv), with Faculty approval.

Students in the Space major do not undertake Integrated Engineering units and should substitute a unit from their major.

Year 4 - Semester 2

Type CP CP From
6 Select from MECH3460: Mechanical Design 2
6 Select from MTRX3700: Mechatronics 3
6 Select from MTRX3760: Mechatronic Systems Design
6 Select from PMGT3855: Project Variance Analysis

Year 5 - Semester 1

Type CP CP From
6 Select from ELEC3204: Power Electronics and Applications
2 Select from ENGG4111: Integrated Engineering 4
6 Select from AMME4111: Thesis A
0 Select from ENGG4000: Practical Experience
6 Select from Unit Block:
Mechatronic Specialist Electives


Note: At least 12 credit points of Mechatronic Elective units must be completed. These may be taken in either semester.
6 Select from Unit Block:
Mechatronic Specialist Electives


Note: At least 12 credit points of Mechatronic Elective units must be completed. These may be taken in either semester.

Note: ENGG4111 may be replaced by ENGG4064/5 Advanced Engineering Design A/B, with Faculty approval.

Students in the Space major do not undertake Integrated Engineering units and should substitute a unit from their major.

Year 5 - Semester 2

Type CP CP From
6 Select from AMME4112: Thesis B
12 Select from Unit Block:
Project Management Electives

4. Pathways

48cp Majors

Type CP CP From

Note: From 2019 onwards, all engineering majors will be converted to the 48 credit point format, and several new majors will be introduced - details can be viewed in the 2019 degree structures.

You can find more information at https://canvas.sydney.edu.au/courses/2806/pages/feit-your-studies-bachelor-of-engineering-majors

Major in Space Engineering (24cp)

Type CP CP From
Core
6 AERO2705: Space Engineering 1


Note: Replacing ENGG1111
Core
6 AERO3760: Space Engineering 2


Note: Replacing MECH3460
Core
6 AERO4701: Space Engineering 3
6 Select from Unit Block Space Specialist Electives

Note: To be eligible for this major students must complete the 24 cp listed. There are ATAR and WAM (>75%) entry requirements for enrolment in this major.

5. Unit Blocks

Block 1 - Space Specialist Electives (Min CP: 6,Max CP: 6)

Unit Code Unit Name CP Sessions Offered
AERO5700 Space Engineering (Advanced) 6 Semester 1
Semester 2
AMME4710 Computer Vision and Image Processing 6 Semester 2
AMME5520 Advanced Control and Optimisation 6 Semester 1
AMME5790 Introduction to Biomechatronics 6 Semester 2
MECH5720 Sensors and Signals 6 Semester 2
MTRX5700 Experimental Robotics 6 Semester 1

Block 2 - Project Management Electives (Min CP: 18,Max CP: 18)

Unit Code Unit Name CP Sessions Offered
PMGT2854 Executing Projects 6 Semester 1
Semester 2
PMGT3856 Sustainability & Knowledge Management 6 Semester 1
PMGT3857 International Project Management 6 Semester 2

Block 3 - Mechatronic Specialist Electives (Min CP: 12,Max CP: 12)

Unit Code Unit Name CP Sessions Offered
AMME4710 Computer Vision and Image Processing 6 Semester 2
AMME5520 Advanced Control and Optimisation 6 Semester 1
AMME5790 Introduction to Biomechatronics 6 Semester 2
MECH5720 Sensors and Signals 6 Semester 2
MTRX5700 Experimental Robotics 6 Semester 1

Block 4 - Engineering Core (Min CP: 36,Max CP: 36)

Unit Code Unit Name CP Sessions Offered
AMME4111 Thesis A 6 Semester 1
Semester 2
AMME4112 Thesis B 6 Semester 1
Semester 2
ENGG1111 Integrated Engineering 1 6 Semester 1
Semester 2
ENGG2111 Integrated Engineering 2 2 Semester 1
Semester 2
Int February
ENGG3111 Integrated Engineering 3 2 Semester 1
Semester 2
ENGG4000 Practical Experience 0 Semester 1
Semester 2
Other
Int January
Int February
Int March
Int April
Int May
Int June
Int July
Int August
Int September
Int October
Int November
Int December
ENGG4111 Integrated Engineering 4 2 Semester 1
Semester 2
MATH1001 Differential Calculus 3 Semester 1
Summer Main
MATH1002 Linear Algebra 3 Semester 1
Summer Main
MATH1003 Integral Calculus and Modelling 3 Semester 2
Summer Main
MATH1005 Statistics 3 Semester 2
Summer Main

Block 5 - Project Management Core (Min CP: 66,Max CP: 66)

Unit Code Unit Name CP Sessions Offered
BUSS1040 Economics for Business Decision Making 6 Semester 1
Semester 2
ENGG1850 Introduction to Project Management 6 Semester 1
ENGG2850 Project Cost and Finance 6 Semester 1
ENGG2851 Project Analytics 6 Semester 1
Summer Main
ENGG2852 Project Based Organisational Behaviour 6 Semester 2
ENGG2855 Project Acceptance 6 Semester 1
Semester 2
ENGG3853 Project Risk Management: Tools & Techniques 6 Semester 1
ENGG3854 Legal Aspects of Projects 6 Semester 1
Semester 2
Summer Main
PMGT1852 Facilitation and Stakeholder Engagement 6 Semester 2
Int June
PMGT3855 Project Variance Analysis 6 Semester 2
PMGT3858 Adapting to Project Context 6 Semester 1

Block 6 - Mechatronic Stream Core (Min CP: 108,Max CP: 108)

Unit Code Unit Name CP Sessions Offered
AMME1362 Materials 1 6 Semester 2
AMME2301 Mechanics of Solids 1 6 Semester 2
AMME2500 Engineering Dynamics 6 Semester 1
AMME3500 System Dynamics and Control 6 Semester 1
ELEC1103 Fundamentals of Electrical and Electronic Engineering 6 Semester 1
ELEC2104 Electronic Devices and Circuits 6 Semester 2
ELEC3204 Power Electronics and Applications 6 Semester 1
ENGG1801 Engineering Computing 6 Semester 1
Summer Late
ENGG1802 Engineering Mechanics 6 Semester 2
Summer Main
Int January
MECH2400 Mechanical Design 1 6 Semester 2
MECH3460 Mechanical Design 2 6 Semester 2
MECH3660 Manufacturing Engineering 6 Semester 1
MTRX1701 Introduction to Mechatronic Engineering 6 Semester 1
MTRX1702 Mechatronics 1 6 Semester 2
MTRX1705 Introduction to Mechatronic Design 6 Semester 2
MTRX2700 Mechatronics 2 6 Semester 1
MTRX3700 Mechatronics 3 6 Semester 2
MTRX3760 Mechatronic Systems Design 6 Semester 2