1. Overview

Course:	Flexible First Year 2016+ / Project Management (2017)
CP Required:	48
Min FT Duration:	1.00 Years
Min PT Duration:	N/A
Faculty/School:	Faculty of Engineering
Years Offered:	2018, 2017, 2016

2. Requirements

To qualify for the award of the combined degree:

(a) For all Bachelor of Engineering combined degrees a candidate must complete 240 credit points and satisfy any additional requirements specified in the following clauses.

(b) Where the requirements specified in the following clauses account for less than the total required credit, candidates must complete additional units of study from the tables relevant to the Bachelor of Engineering as may be necessary to satisfy the requirements of the degree.

Requirements for the Bachelor of Engineering

For the Bachelor of Engineering component of a combined degree:

(a) The units of study that may be taken for the Bachelor of Engineering component of the combined degree are set out in the tables of units of study for the Bachelor of Engineering single degree;

(b) Except where approved, all candidates must complete a minimum of 144 credit points comprising:

(i) 36cp from the Engineering Core Table, including all required units;

(ii) 108cp from the Engineering Stream Core Table pertaining to the specialist stream being undertaken, including all required units;

(c) The Faculty Board may approve, based on appropriate academic justification, a list of approved unit alternatives. These alternatives specify, for particular Engineering stream / combined degree combinations, units within the normal requirements for the Bachelor of Engineering component of the combined degree that can be replaced by specified alternative units that would form part of the normal program for single degree students in that stream.

Requirements for the Bachelor of Project Management

For the Bachelor of Project Management component of a combined degree:

(a) Candidates must complete the core units of study as set out in the Bachelor of Project Management Unit of Study Table.

Engineering Honours Requirements

(a) an EWAM of at least 65 immediately prior to the semester in which a thesis unit of study is first attempted; and

(b) have an EIHWAM of at least 65 at the completion of the degree; and

(c) complete the requirements within a time limit of 5 years for a single Bachelor of Engineering Honours degree or complete the requirements within a time limit of 6 years for a combined Bachelor of Engineering Honours combined degree.

Candidates who satisfy the requirements for the Engineering degree, but who have not satisfied each of Clauses (a), (b) and (c), will qualify for the award of the Bachelor of Engineering degree (i.e. the PASS degree, awarded without Honours).

Advanced units in Maths and Science

Most units of study offered by the Science Faculty on the list of core requirements can be replaced by an equivalent advanced level unit; subject to prerequisite conditions (as required by the Faculty of Science) being met. Students considering doing advanced options should seek advice from their department before enrolling.

Study Abroad

Students undertaking Study Abroad in a particular year of their degree must enrol in the appropriate International Exchange Program units of study as an alternative to a semester`s standard units.

Permission from the relevant Head of School must be sought prior to enrolling in exchange units of study.

Faculty Resolutions

Details of relevant Faculty resolutions are available via the university handbook site at: http://sydney.edu.au/handbooks/

3. Semesters

Note: ENGG1111 may be replaced by ENGG1061 Advanced Engineering for approved students. MATH1001 and MATH1002 may be replaced by advanced units MATH1901 and MATH1902.

Students choose a stream of engineering to undertake at the end of Semester 1. In semester 2 they then follow the program for that particular engineering stream.

Note: MATH1003 and MATH1005 may be replaced by advanced units MATH1903 and MATH1905.

This semester`s units should only be used as an enrolment guide, the selection of the stream is required at the end of Semester 1, in which case, your enrolment should follow the selected Stream. Note that the MATH units will remain regardless of the selected stream.

4. Pathways

No streams/majors defined for this course version.

5. Unit Blocks

Block 1 - Engineering Core (Min CP: 18,Max CP: 18)

Unit Code	Unit Name	CP	Sessions Offered
ENGG1111	Integrated Engineering 1	6	Semester 1 Semester 2
MATH1001	Differential Calculus	3	Semester 1 Summer Main
MATH1002	Linear Algebra	3	Semester 1 Summer Main
MATH1003	Integral Calculus and Modelling	3	Semester 2 Summer Main
MATH1005	Statistics	3	Semester 2 Summer Main
MATH1901	Differential Calculus (Advanced)	3	Semester 1
MATH1902	Linear Algebra (Advanced)	3	Semester 1
MATH1903	Integral Calculus and Modelling Advanced	3	Semester 2
MATH1905	Statistics (Advanced)	3	Semester 2

Block 2 - Flexible First Year units (Min CP: 18,Max CP: 30)

Unit Code	Unit Name	CP	Sessions Offered
ENGG1000	History and Philosophy of Engineering	6	Semester 1 Semester 2
ENGG1800	Introduction to Engineering Disciplines	6	Semester 1
ENGG1801	Engineering Computing	6	Semester 1 Int January
ENGG1802	Engineering Mechanics	6	Semester 2 Summer Main Int January
ENGG1813	Engineering Critical Thinking	6	Semester 2

Block 3 - Project Management Core (Min CP: 12,Max CP: 12)

Unit Code	Unit Name	CP	Sessions Offered
ENGG1850	Introduction to Project Management	6	Semester 1
PMGT1852	Facilitation and Stakeholder Engagement	6	Semester 2 Int June
PSYC1002	Psychology 1002	6	Semester 2 Summer Main

Note: PSYC1002 has been replaced by PMGT1852 in 2017