1. Overview

Course:	Flexible First Year 2019+ / Project Management (2021)
CP Required:	48
Min FT Duration:	1.00 Years
Min PT Duration:	N/A
Faculty/School:	Faculty of Engineering
Years Offered:	2024, 2023, 2022, 2021, 2020, 2019

2. Requirements

The handbook rules governing this degree are as follows:

To qualify for the award of the combined degree:

(a) For all Bachelor of Engineering combined degrees a candidate must complete 240 credit points and satisfy any additional requirements specified.

(b) Where the requirements specified in the following clauses account for less than the total required credit, candidates must complete additional units of study from the tables relevant to the Bachelor of Engineering as may be necessary to satisfy the requirements of the degree.

Requirements for the Bachelor of Engineering Honours

(a) The units of study that may be taken for the Bachelor of Engineering Honours component of the combined degree are set out in the tables of units of study for the Bachelor of Engineering Honours single degree;

(b) Except where varied by other clauses of these resolutions, all candidates must complete a minimum of 144 credit points comprising:

(i) 36 credit points from the Engineering Core Table, including all required units;

(ii) 108 credit points from the Engineering Stream Core Table pertaining to the specialist stream being undertaken, including all required units;

(c) The Faculty Board may approve, based on appropriate academic justification, a list of approved unit alternatives. These alternatives specify, for particular Engineering stream / combined degree combinations, units within the normal requirements for the Bachelor of Engineering Honours component of the combined degree that can be replaced by specified alternative units that would form part of the normal program for single degree students in that stream.

Requirements for the Bachelor of Project Management

For the Bachelor of Project Management component of a combined degree:

(a) Candidates must complete the core and elective units of study as set out in the Bachelor of Project Management Unit of Study Table.

Advanced units in Maths and Science

Most units of study offered by the Science Faculty on the list of core requirements can be replaced by an equivalent advanced level unit; subject to prerequisite conditions (as required by the Faculty of Science) being met. Students considering doing advanced options should seek advice from their department before enrolling.

Study Abroad

Students undertaking Study Abroad in a particular year of their degree must enrol in the appropriate International Exchange Program units of study as an alternative to a semester`s standard units.

Permission from the relevant Head of School must be sought prior to enrolling in exchange units of study.

Faculty Resolutions

Details of relevant Faculty resolutions are available via the university handbook site at: http://sydney.edu.au/handbooks/

3. Semesters

Note: MATH1021 and MATH1002 may be replaced by advanced units MATH1921 and MATH1902.

Students choose a stream of engineering to undertake at the end of Semester 1. In semester 2 they then follow the program for that particular engineering stream.

Note: MATH1023 and MATH1005 may be replaced by advanced units MATH1923 and MATH1905.

This semester's units should only be used as a temporary enrolment. At the end of Semester 1 you should select your stream and change your unit selection to the appropriate units for that stream. Note that the MATH units should be taken regardless of which stream is selected.

4. Pathways

No streams/majors defined for this course version.

5. Unit Blocks

Block 1 - Foundation, Intro Computing, and Professional Engagement Program (PEP) units (Min CP: 18,Max CP: 18)

Unit Code	Unit Name	CP	Sessions Offered
ENGG1810	Introduction to Engineering Computing	6	Semester 1 Semester 2 Int February
ENGP1001	Professional Engagement Program 1A	0	Semester 1 Semester 2
ENGP1002	Professional Engagement Program 1B	0	Semester 1 Semester 2
MATH1002	Linear Algebra	3	Semester 1 Semester 2 Summer Main
MATH1005	Statistical Thinking with Data	3	Semester 1 Semester 2 Int January
MATH1021	Calculus of One Variable	3	Semester 1 Semester 2
MATH1023	Multivariable Calculus and Modelling	3	Semester 1 Semester 2
MATH1902	Linear Algebra (Advanced)	3	Semester 1
MATH1905	Statistics (Advanced)	3	Semester 2
MATH1921	Calculus of One Variable (Adv)	3	Semester 1
MATH1923	Multivariable Calculus and Modelling (Adv)	3	Semester 2

Block 2 - Project 1 Units (Min CP: 6,Max CP: 6)

Unit Code	Unit Name	CP	Sessions Offered
AERO1560	Introduction to Aerospace Engineering	6	Semester 1
BMET1960	Biomedical Engineering 1A	6	Semester 1
CHNG1108	Introduction to Chemical Engineering	6	Semester 1
CIVL1900	Introduction to Civil Engineering	6	Semester 1
ELEC1004	Practical Introduction to Electrical Engineering	6	Semester 1
MECH1560	Introduction to Mechanical Engineering	6	Semester 1
MTRX1701	Introduction to Mechatronic Engineering	6	Semester 1

Block 3 - Flexible First Year units (Min CP: 12,Max CP: 12)

Unit Code	Unit Name	CP	Sessions Offered
ENGF1661	Flexible First Year Enrolment 1	6	Semester 2
ENGF1662	Flexible First Year Enrolment 2	6	Semester 2

Block 10 - Project Management Core (Min CP: 12,Max CP: 12)

Unit Code	Unit Name	CP	Sessions Offered
ENGG1850	Introduction to Project Management	6	Semester 1
ENGG1865	Project Time, Cost and Resources	6	Semester 2