1. Overview

Course:	Aeronautical / Arts (2022 and earlier) (2016)
CP Required:	240
Min FT Duration:	5.00 Years
Min PT Duration:	5.00 Years
Faculty/School:	Faculty of Engineering
Years Offered:	2022, 2021, 2020, 2019, 2018, 2017, 2016, 2015

2. Requirements

In summary the requirements are:

Students must complete 240 credit points as follows:

Engineering (156 credit points):

► 36 credit points of Engineering core units

► 108 credit points of Aeronautical stream core units

► 12 credit points of Aeronautical Specialist elective units

Arts:

► 84 credit points of Arts units

The handbook rules governing this degree are as follows:

To qualify for the award of the combined degree:

(a) For all Bachelor of Engineering combined degrees a candidate must complete 240 credit points and satisfy any additional requirements specified.

(b) Where the requirements specified in the following clauses account for less than the total required credit, candidates must complete additional units of study from the tables relevant to the Bachelor of Engineering as may be necessary to satisfy the requirements of the degree.

Requirements for the Bachelor of Engineering

For the Bachelor of Engineering component of a combined degree:

(a) The units of study that may be taken for the Bachelor of Engineering component of the combined degree are set out in the tables of units of study for the Bachelor of Engineering single degree;

(b) Except where approved, all candidates must complete a minimum of 144 credit points comprising:

(i) 36cp from the Engineering Core Table, including all required units;

(ii) 108cp from the Engineering Stream Core Table pertaining to the specialist stream being undertaken, including all required units;

(c) The Faculty Board may approve, based on appropriate academic justification, a list of approved unit alternatives. These alternatives specify, for particular Engineering stream / combined degree combinations, units within the normal requirements for the Bachelor of Engineering component of the combined degree that can be replaced by specified alternative units that would form part of the normal program for single degree students in that stream.

Candidates who do not meet the requirements for the award of the Bachelor of Engineering Honours but who have otherwise satisfied the requirements of the Bachelor of Engineering shall graduate with the Bachelor of Engineering pass degree.

Requirements for the Bachelor of Arts

For the Bachelor of Arts component of a combined degree:

(a) The units of study that may be taken are set out in Table A from the Faculty of Arts and Social Sciences Tables of units of study.

(b) Candidates must complete a total of 84 credit points from Table A, including:

(i) a major from Table A

(ii) a minimum of 54 credit points of 2000/3000 level units of study.

Candidates for the award of the Bachelor of Arts (Honours) who do not meet the requirements, and who have not already graduated, will be awarded the Bachelor of Arts pass degree.

Engineering Honours requirements

(a) an EWAM of at least 65 immediately prior to the semester in which a thesis unit of study is first attempted; and

(b) have an EIHWAM of at least 65 at the completion of the degree; and

(c) complete the requirements within a time limit of 5 years for a single Bachelor of Engineering Honours degree or complete the requirements within a time limit of 6 years for a combined Bachelor of Engineering Honours combined degree.

Candidates who satisfy the requirements for the Engineering degree, but who have not satisfied each of Clauses (a), (b) and (c), will qualify for the award of the Bachelor of Engineering degree (i.e. the PASS degree, awarded without Honours).

Advanced units in Maths and Science

Most units of study offered by the Science Faculty on the list of core requirements can be replaced by an equivalent advanced level unit; subject to prerequisite conditions (as required by the Faculty of Science) being met. Students considering doing advanced options should seek advice from their department before enrolling.

Study Abroad

Students undertaking Study Abroad in a particular year of their degree must enrol in the appropriate International Exchange Program units of study as an alternative to a semester`s standard units.

Permission from the relevant Head of School must be sought prior to enrolling in exchange units of study.

Majors

A major requires:

(a) the completion of 24 credit points chosen from units of study listed in the table for that major;

(b) satisfying any additional requirements specified for the major, and listed with the table of units for the major;

(c) the completion of a thesis project that has been approved by the Head of School (or delegate) as relevant to the topic of the major.

Faculty Resolutions

Details of relevant Faculty resolutions are available via the university handbook site at: http://sydney.edu.au/handbooks/

3. Semesters

Note: MATH1021 and MATH1002 may be replaced by advanced units MATH1921 and MATH1902.

Note: MATH1023 and MATH1005 may be replaced by advanced units MATH1923 and MATH1905.

Note: ENGG1111 may be replaced by ENGG1061 Advanced Engineering for approved students.

Students in the Space major do not undertake Integrated Engineering units and should substitute a unit from their major.

Note: ENGG2111 may be replaced by ENGG2062 Engineering Project: Business Plan 2 Adv, with Faculty approval.

Students in the Space major do not undertake Integrated Engineering units and should substitute a unit from their major.

Note: ENGG3111 may be replaced by ENGG3062 Technology Education (Adv), with Faculty approval.

Students in the Space major do not undertake Integrated Engineering units and should substitute a unit from their major.

Note: ENGG4111 may be replaced by ENGG4064/5 Advanced Engineering Design A/B, with Faculty approval.

Students in the Space major do not undertake Integrated Engineering units and should substitute a unit from their major.

4. Pathways

48cp Majors

Type

CP

CP From

Note: From 2019 onwards, all engineering majors will be converted to the 48 credit point format, and several new majors will be introduced - details can be viewed in the 2019 degree structures.

You can find more information at https://canvas.sydney.edu.au/courses/2806/pages/feit-your-studies-bachelor-of-engineering-majors

Major in Space Engineering (24cp)

Type	CP	CP From
Core	6	AERO2705: Space Engineering 1 Note: Replacing ENGG1111
Core	6	AERO3760: Space Engineering 2 Note: Replacing AERO2703
Core	6	AERO4701: Space Engineering 3 Note: Replacing AERO4460
Space Specialist Electives	6	Select from Unit Block Space Specialist Electives

Note: Students are required to complete 24cp as per the table to be eligible of this major. There are minimum ATAR or WAM (>75%) entry requirements for enrolment in this major.

This Engineering major can be taken along with any of the available Arts majors.

5. Unit Blocks

Block 1 - Arts Units (Min CP: 84,Max CP: 84)

Note: For the Bachelor of Arts component, students are required to complete a total of 84 credit points of Table A units as listed in the handbook of the Faculty of Arts and Social Sciences, including a major from Table A and a minimum 54 credit points of 2000/3000 level units of study. See Faculty handbooks at http://sydney.edu.au/handbooks

Block 2 - Aeronautical Specialist Electives (Min CP: 12,Max CP: 12)

Unit Code	Unit Name	CP	Sessions Offered
AERO4260	Aerodynamics 2	6	Semester 1
AERO4360	Aerospace Structures 2	6	Semester 1
AERO4560	Flight Mechanics 2	6	Semester 2

Block 3 - Space Specialist Electives (Min CP: 6,Max CP: 6)

Unit Code	Unit Name	CP	Sessions Offered
AERO4260	Aerodynamics 2	6	Semester 1
AERO4360	Aerospace Structures 2	6	Semester 1
AERO4560	Flight Mechanics 2	6	Semester 2
AERO5700	Space Engineering (Advanced)	6	Semester 1 Semester 2

Block 4 - Engineering Core (Min CP: 36,Max CP: 36)

Unit Code	Unit Name	CP	Sessions Offered
AMME4111	Thesis A	6	Semester 1 Semester 2
AMME4112	Thesis B	6	Semester 1 Semester 2
ENGG1111	Integrated Engineering 1	6	Semester 1
ENGG2111	Integrated Engineering 2	2	Semester 1 Semester 2 Int February
ENGG3111	Integrated Engineering 3	2	Semester 1 Semester 2
ENGG4000	Practical Experience	0	Int January Int February Int March Int April Int May Int June Int July Int August Int September Int October Int November Int December
ENGG4111	Integrated Engineering 4	2	Semester 1
MATH1001	Differential Calculus	3	Semester 1 Summer Main
MATH1002	Linear Algebra	3	Semester 1 Semester 2 Summer Main
MATH1003	Integral Calculus and Modelling	3	Semester 2 Summer Main
MATH1005	Statistical Thinking with Data	3	Semester 1 Semester 2 Int January

Block 5 - Aeronautical Stream Core (Min CP: 108,Max CP: 108)

Unit Code	Unit Name	CP	Sessions Offered
AERO1560	Introduction to Aerospace Engineering	6	Semester 1
AERO2703	Aircraft Performance and Operations	6	Semester 2
AERO3260	Aerodynamics 1	6	Semester 2
AERO3261	Propulsion	6	Semester 1
AERO3360	Aerospace Structures 1	6	Semester 1
AERO3460	Aerospace Design 1	6	Semester 1
AERO3560	Flight Mechanics 1	6	Semester 2
AERO4460	Aerospace Design 3	6	Semester 1
AMME1362	Introduction to Engineering Materials	6	Semester 2
AMME2261	Fluid Mechanics 1	6	Semester 1
AMME2262	Introduction to Thermal Engineering	6	Semester 2
AMME2301	Mechanics of Solids	6	Semester 2
AMME2500	Engineering Dynamics	6	Semester 1
AMME2700	Instrumentation	6	Semester 1
AMME3500	System Dynamics and Control	6	Semester 1
ENGG1801	Engineering Computing	6	Semester 1 Int January
ENGG1802	Engineering Mechanics	6	Semester 2 Summer Main Int January
MECH2400	Mechanical Systems Design 1	6	Semester 1