Faculty of Engineering

School of Civil Engineering

Civil / Design in Architecture (2019)


Note: This course version applies only to students first enrolling in 2019.
WARNING: This course version is currently under review and is subject to change.


1. Overview

Course: Civil / Design in Architecture (2019)
CP Required: 240
Min FT Duration: 5.00 Years
Min PT Duration: N/A
Faculty/School: School of Civil Engineering
Years Offered: 2025, 2024, 2023, 2022, 2021, 2020, 2019, 2018, 2017, 2016, 2015

2. Requirements

Summary

In summary the requirements are:

Students must complete 240 credit points as follows:

Engineering (144 credit points):

► 36 credit points of Engineering core units

► The Professional Engagement Program comprising ENGP1000 (0cp), ENGP2000 (0cp) and ENGP3000 (0cp)

► 108 credit points of Civil stream core units

Architecture:

► 90 credit points of Architecture core units

► 6 credit points of Architecture elective units

The handbook rules governing this degree are as follows:

To qualify for the award of the combined degree:

(a) For all Bachelor of Engineering combined degrees a candidate must complete 240 credit points and satisfy any additional requirements specified.

(b) Where the requirements specified in the following clauses account for less than the total required credit, candidates must complete additional units of study from the tables relevant to the Bachelor of Engineering as may be necessary to satisfy the requirements of the degree.

Requirements for the Bachelor of Engineering Honours

(a) The units of study that may be taken for the Bachelor of Engineering Honours component of the combined degree are set out in the tables of units of study for the Bachelor of Engineering Honours single degree;

(b) Except where varied by other clauses of these resolutions, all candidates must complete a minimum of 144 credit points comprising:

(i) 36 credit points from the Engineering Core Table, including all required units;

(ii) 108 credit points from the Engineering Stream Core Table pertaining to the specialist stream being undertaken, including all required units;

(c) The Faculty Board may approve, based on appropriate academic justification, a list of approved unit alternatives. These alternatives specify, for particular Engineering stream / combined degree combinations, units within the normal requirements for the Bachelor of Engineering Honours component of the combined degree that can be replaced by specified alternative units that would form part of the normal program for single degree students in that stream.

Requirements for the Bachelor of Design Architecture

For the Bachelor of Design in Architecture component of a combined degree:

(a) Candidates must complete 96 credit points of units of study from the Bachelor of Engineering Honours (Civil) and Bachelor of Design in Architecture - Architecture Table.

Advanced units in Maths and Science

Most units of study offered by the Science Faculty on the list of core requirements can be replaced by an equivalent advanced level unit; subject to prerequisite conditions (as required by the Faculty of Science) being met. Students considering doing advanced options should seek advice from their department before enrolling.

Study Abroad

Students undertaking Study Abroad in a particular year of their degree must enrol in the appropriate International Exchange Program units of study as an alternative to a semester`s standard units.

Permission from the relevant Head of School must be sought prior to enrolling in exchange units of study.

Faculty Resolutions

Details of relevant Faculty resolutions are available via the university handbook site at: http://sydney.edu.au/handbooks/

3. Semesters

Year 1 - Semester 1

Type CP CP From
0 Select from DESA1555: Safety Induction and Competency Unit
3 Select from MATH1021: Calculus of One Variable
12 Select from BDES1026: Architecture Studio 1A
3 Select from MATH1002: Linear Algebra
6 Select from BDES1011: Architectural History/Theory 1
0 Select from ENGP1000: Professional Engagement Program 1


Note: All students must enrol in ENGP1000 in their first semester of enrolment.

New ENGP units will be in place from 2021. You can find more information at https://canvas.sydney.edu.au/courses/2806/pages/professional-engagement-program-pep-2021-changes

Note: From 2024, 3cp Math units are replaced by new 6cp units MATH1061 and MATH1062. Students who have not yet completed all 3cp Math units can use this interactive tool on Canvas for enrolment advice: https://canvas.sydney.edu.au/courses/2806/pages/mathematics-changes-in-2024

Year 1 - Semester 2

Type CP CP From
3 Select from MATH1023: Multivariable Calculus and Modelling
3 Select from MATH1005: Statistical Thinking with Data
12 Select from BDES1027: Architecture Studio 1B
6 Select from BDES1023: Architectural Technologies 1

Note: From 2024, 3cp Math units are replaced by new 6cp units MATH1061 and MATH1062. Students who have not yet completed all 3cp Math units can use this interactive tool on Canvas for enrolment advice: https://canvas.sydney.edu.au/courses/2806/pages/mathematics-changes-in-2024

Year 2 - Semester 1

Type CP CP From
6 Select from CIVL1900: Introduction to Civil Engineering
6 Select from ENGG1801: Engineering Computing
6 Select from ENGG1111: Integrated Engineering 1
6 Select from CIVL2110: Materials


Note: CIVL1110 replaces CIVL2110 from 2022.

Year 2 - Semester 2

Type CP CP From
6 Select from CIVL1802: Statics
6 Select from CIVL2812: Project Appraisal
6 Select from CIVL1810: Engineering Construction and Surveying
0 Select from ENGP2000: Professional Engagement Program 2


Note: New ENGP units will be in place from 2021. You can find more information at https://canvas.sydney.edu.au/courses/2806/pages/professional-engagement-program-pep-2021-changes
6 Select from GEOL1501: Engineering Geology 1


Note: From 2024, CIVL1022 replaces GEOL1501. Students who have not yet completed GEOL1501 should enrol in CIVL1022.

Year 3 - Semester 1

Type CP CP From
6 Select from BDES2013: Architectural Technologies 2
6 Select from CIVL2201: Structural Mechanics
12 Select from BDES2026: Architecture Studio 2A

Year 3 - Semester 2

Type CP CP From
6 Select from CIVL2611: Introductory Fluid Mechanics
6 Select from CIVL2410: Soil Mechanics 1
12 Select from BDES2027: Architecture Studio 2B
2 Select from ENGG2111: Integrated Engineering 2

Year 4 - Semester 1

Type CP CP From
6 Select from CIVL3205: Concrete Structures 1
6 Select from MATH2061: Linear Mathematics and Vector Calculus
12 Select from BDES3026: Architecture Studio 3A
2 Select from ENGG3111: Integrated Engineering 3

Year 4 - Semester 2

Type CP CP From
6 Select from CIVL3206: Steel Structures 1
6 Select from CIVL3235: Structural Analysis
12 Select from BDES3027: Architecture Studio 3B

Year 5 - Semester 1

Type CP CP From
2 Select from ENGG4111: Integrated Engineering 4
6 Select from CIVL4903: Civil Engineering Design
6 Select from CIVL4022: Thesis A
6 Select from CIVL3612: Fluid Mechanics
6 Select from Unit Block:
Architecture Elective
0 Select from ENGP3000: Professional Engagement Program 3


Note: New ENGP units will be in place from 2021. You can find more information at https://canvas.sydney.edu.au/courses/2806/pages/professional-engagement-program-pep-2021-changes

Note: Students must choose a 6cp Architecture elective in Year 5, either Semester 1 or Semester 2.

Year 5 - Semester 2

Type CP CP From
6 Select from CIVL4860: Architectural to Structural Design
6 Select from CIVL3811: Engineering Design and Construction
6 Select from CIVL4023: Thesis B

Note: Students must choose a 6cp Architecture elective in Year 5, either Semester 1 or Semester 2.

4. Pathways

No streams/majors defined for this course version.

5. Unit Blocks

Block 1 - Engineering Core (Min CP: 36,Max CP: 48)

Unit Code Unit Name CP Sessions Offered
AMME4010 Major Industrial Project 24 Semester 1
Semester 2
AMME4111 Thesis A 6 Semester 1
Semester 2
AMME4112 Thesis B 6 Semester 1
Semester 2
CHNG4203 Major Industrial Project 24 Semester 1
Semester 2
CHNG4811 Thesis A 6 Semester 1
Semester 2
CHNG4812 Thesis B 6 Semester 1
Semester 2
CIVL4022 Thesis A 6 Semester 1
Semester 2
CIVL4023 Thesis B 6 Semester 1
Semester 2
ELEC4712 Thesis A 6 Semester 1
Semester 2
ELEC4713 Thesis B 6 Semester 1
Semester 2
ELEC4714 Major Industrial Project 24 Semester 1
Semester 2
ENGG1111 Integrated Engineering 1 6 Semester 1
ENGG2111 Integrated Engineering 2 2 Semester 1
Semester 2
Int February
ENGG3111 Integrated Engineering 3 2 Semester 1
Semester 2
ENGG4111 Integrated Engineering 4 2 Semester 1
ENGP1000 Professional Engagement Program 1 0 Semester 1
Semester 2
ENGP2000 Professional Engagement Program 2 0 Semester 1
Semester 2
ENGP3000 Professional Engagement Program 3 0 Semester 1
Semester 2
MATH1002 Linear Algebra 3 Semester 1
Semester 2
Summer Main
MATH1005 Statistical Thinking with Data 3 Semester 1
Semester 2
Int January
MATH1021 Calculus of One Variable 3 Semester 1
Semester 2
MATH1023 Multivariable Calculus and Modelling 3 Semester 1
Semester 2
MATH1902 Linear Algebra (Advanced) 3 Semester 1
MATH1905 Statistics (Advanced) 3 Semester 2
MATH1921 Calculus of One Variable (Adv) 3 Semester 1
MATH1923 Multivariable Calculus and Modelling (Adv) 3 Semester 2

Note: Complete a minimum of 36cp including:

- ENGP1000 (0cp), ENGP2000 (0cp) and ENGP3000 (0cp)

- Exactly 12cp of Integrated Engineering units comprising ENGG1111 (6cp), ENGG2111 (2cp), ENGG3111 (2cp) and ENGG4111 (2cp)

- Exactly 12cp of MATH1xxx units: MATH1021 Calculus of One Variable (3cp) AND MATH1002 Linear Algebra (3cp) AND MATH1023 Multivariable Calculus and Modelling (3cp) AND MATH1005 Statistics (3cp)

- A minimum of 12cp of (see note 1) from either AMME4111-4112 Thesis A & B (6cp+6cp) OR CHNG4811-CHNG4812 Thesis A & B (6cp+6cp) OR CIVL4022-4023 Thesis A & B (6cp+6cp) OR ELEC4712-4713 Thesis A & B (6cp+6cp) OR AMME4010 Major Industrial Project (24cp) OR CHNG4203 Major Industrial Project (24cp) OR ELEC4714 Major Industrial Project (24cp)

Note 1. All Thesis A units are mutually prohibited (meaning that only one can be completed), and all Thesis B units have the associated Thesis A unit as a pre-requisite. Students may undertake only the Thesis units relevant to their stream.

Block 2 - Civil Core (Min CP: 108,Max CP: 108)

Unit Code Unit Name CP Sessions Offered
CIVL1802 Statics 6 Semester 1
Int January
Int July
CIVL1810 Engineering Construction and Surveying 6 Semester 2
CIVL1900 Introduction to Civil Engineering 6 Semester 1
CIVL2110 Materials 6 Semester 1
Semester 2
CIVL2201 Structural Mechanics 6 Semester 1
CIVL2410 Soil Mechanics 1 6 Semester 2
CIVL2611 Introductory Fluid Mechanics 6 Semester 2
CIVL2812 Project Appraisal 6 Semester 2
CIVL3205 Concrete Structures 1 6 Semester 1
CIVL3206 Steel Structures 1 6 Semester 2
CIVL3235 Structural Analysis 6 Semester 2
CIVL3612 Fluid Mechanics 6 Semester 1
CIVL3811 Engineering Design and Construction 6 Semester 2
CIVL4860 Architectural to Structural Design 6 Semester 2
CIVL4903 Civil Engineering Design 6 Semester 1
Semester 2
ENGG1801 Engineering Computing 6 Semester 1
Int January
GEOL1501 Engineering Geology 1 6 Semester 2
MATH2061 Linear Mathematics and Vector Calculus 6 Semester 1
Summer Main

Block 3 - Architecture Core (Min CP: 90,Max CP: 90)

Unit Code Unit Name CP Sessions Offered
BDES1011 Architectural History/Theory 1 6 Semester 1
BDES1023 Architectural Technologies 1 6 Semester 2
BDES1026 Architecture Studio 1A 12 Semester 1
BDES1027 Architecture Studio 1B 12 Semester 2
BDES2013 Architectural Technologies 2 6 Semester 1
Semester 2
BDES2026 Architecture Studio 2A 12 Semester 1
BDES2027 Architecture Studio 2B 12 Semester 2
BDES3026 Architecture Studio 3A 12 Semester 1
BDES3027 Architecture Studio 3B 12 Semester 2
DESA1555 Safety Induction and Competency Unit 0 Semester 1
Semester 2

Block 4 - Architecture Elective (Min CP: 6,Max CP: 6)

Unit Code Unit Name CP Sessions Offered
BDES2024 Art Workshop 2 6 Semester 2
BDES3011 Architectural History/Theory 3 6 Semester 1
BDES3025 Architectural Professional Practice 6 Semester 2

Note: This elective can be done either semester (In first semester BDES3011 is available).