The University of Sydney - Engineering

Note: To be eligible for this major, students are required to meet progression requirements. There are ATAR/WAM entry requirements for this major.

Achievement of a major in Space Engineering requires:

(i) 6 credit points of 1000-level selective units

► MECH1560 Introduction to Mechanical Engineering

(ii) 6 credit points of 2000-level major core

► AERO2705 Space Engineering 1 (Taken in Year 2 Semester 2, in place of a Specialist Electives slot)

(iii) 6 credit points of 3000-level major core

► AERO3760 Space Engineering 2 (Taken in Year 3 Semester 2, in place of exempted unit MECH3460)

(iv) 6 credit points of 4000-level major core

► AERO4701 Space Engineering 3 (Taken in Year 5 Semester 1, in place of 6CP General Electives)

(v) 12 credit points of 4000-level project units

► AMME4111 Thesis A and AMME4112 Thesis B taken during final year of studies.

and (vi) 12 credit points of 3000-level and higher selective units of study from Space Specialist Electives.

Note: Mechanical Core unit MECH3660 Manufacturing Engineering (normally taken in Year 4 Semester 1) should be taken in Year 3 Semester 1 in place of exempted unit AMME2000.

Note: Complete a minimum of 36cp including:

- ENGP1000 (0cp), ENGP2000 (0cp) and ENGP3000 (0cp)

- Exactly 12cp of Integrated Engineering units comprising ENGG1111 (6cp), ENGG2111 (2cp), ENGG3111 (2cp) and ENGG4111 (2cp)

- Exactly 12cp of MATH1xxx units: MATH1021 Calculus of One Variable (3cp) AND MATH1002 Linear Algebra (3cp) AND MATH1023 Multivariable Calculus and Modelling (3cp) AND MATH1005 Statistics (3cp)

- A minimum of 12cp of (see note 1) from either AMME4111-4112 Thesis A & B (6cp+6cp) OR CHNG4811-CHNG4812 Thesis A & B (6cp+6cp) OR CIVL4022-4023 Thesis A & B (6cp+6cp) OR ELEC4712-4713 Thesis A & B (6cp+6cp) OR AMME4010 Major Industrial Project (24cp) OR CHNG4203 Major Industrial Project (24cp) OR ELEC4714 Major Industrial Project (24cp)

Note 1. All Thesis A units are mutually prohibited (meaning that only one can be completed), and all Thesis B units have the associated Thesis A unit as a pre-requisite. Students may undertake only the Thesis units relevant to their stream or major.

Note: At least 7 units (42 cp) must be completed.

For 2023 only, ENGG3216 Management of Technological Innovation may be counted as a Mechanical Specialist Elective.

Note: Students may take 6 credit points of free general electives to complete the total number of credit points for their degree. Students may take the following units of study as free general electives, provided they satisfy any prerequisite, quota, departmental permission or any other requirements of the units, and the units are not essentially the same or prohibited units for any of the other units in their degree.

(1) Any units of study from the Faculties of: (i) Engineering and Information Technologies (ii) Science (iii) Arts (iv) Sydney Business School

(2) Any other units of study approved by the Faculty of Engineering and Information Technologies Courses Committee, which will be published in an appropriate place by the Faculty.

(3) Any units of study approved by the Dean (or his/her delegate in these matters), or by the relevant Head of School or Program Director, on a case by case basis upon application by the student.

Note: These units are only available to students enrolled in the Space major. ATAR/WAM requirements apply.