2. Requirements

In summary the requirements are:

Students must complete 240 credit points as follows:

Engineering (156 credit points):

► 36 credit points of Engineering core units

► 102 credit points of Civil stream core units

► 12 credit points of Civil Specialist depth units

► 6 credit points of Civil Specialist breadth units

Project Management:

► 66 credit points of Project Management core units

► 18 credit points of Project Management elective units

The handbook rules governing this degree are as follows:

To qualify for the award of the combined degree:

(a) For all Bachelor of Engineering combined degrees a candidate must complete 240 credit points and satisfy any additional requirements specified.

(b) Where the requirements specified in the following clauses account for less than the total required credit, candidates must complete additional units of study from the tables relevant to the Bachelor of Engineering as may be necessary to satisfy the requirements of the degree.

Requirements for the Bachelor of Engineering

For the Bachelor of Engineering component of a combined degree:

(a) The units of study that may be taken for the Bachelor of Engineering component of the combined degree are set out in the tables of units of study for the Bachelor of Engineering single degree;

(b) Except where approved, all candidates must complete a minimum of 144 credit points comprising:

(i) 36cp from the Engineering Core Table, including all required units;

(ii) 108cp from the Engineering Stream Core Table pertaining to the specialist stream being undertaken, including all required units;

(c) The Faculty Board may approve, based on appropriate academic justification, a list of approved unit alternatives. These alternatives specify, for particular Engineering stream / combined degree combinations, units within the normal requirements for the Bachelor of Engineering component of the combined degree that can be replaced by specified alternative units that would form part of the normal program for single degree students in that stream.

Candidates who do not meet the requirements for the award of the Bachelor of Engineering Honours but who have otherwise satisfied the requirements of the Bachelor of Engineering shall graduate with the Bachelor of Engineering pass degree.

Requirements for the Bachelor of Project Management

For the Bachelor of Project Management component of a combined degree:

(a) Candidates must complete the core units of study as set out in the Bachelor of Project Management Unit of Study Table.

(b) 18cp from the Project Management Electives Table must be completed.

Engineering Honours Requirements

(a) an EWAM of at least 65 immediately prior to the semester in which a thesis unit of study is first attempted; and

(b) have an EIHWAM of at least 65 at the completion of the degree; and

(c) complete the requirements within a time limit of 5 years for a single Bachelor of Engineering Honours degree or complete the requirements within a time limit of 6 years for a combined Bachelor of Engineering Honours combined degree.

Candidates who satisfy the requirements for the Engineering degree, but who have not satisfied each of Clauses (a), (b) and (c), will qualify for the award of the Bachelor of Engineering degree (i.e. the PASS degree, awarded without Honours).

Advanced units in Maths and Science

Most units of study offered by the Science Faculty on the list of core requirements can be replaced by an equivalent advanced level unit; subject to prerequisite conditions (as required by the Faculty of Science) being met. Students considering doing advanced options should seek advice from their department before enrolling.

Study Abroad

Students undertaking Study Abroad in a particular year of their degree must enrol in the appropriate International Exchange Program units of study as an alternative to a semester`s standard units.

Permission from the relevant Head of School must be sought prior to enrolling in exchange units of study.

Faculty Resolutions

Details of relevant Faculty resolutions are available via the university handbook site at: http://sydney.edu.au/handbooks/

3. Semesters

Year 1 - Semester 1

Type	CP	CP From
Engineering Core	3	Select from MATH1001: Differential Calculus Note: This unit is discontinued from 2018. Replacement unit is MATH1021.
Civil Core	6	Select from CIVL1900: Introduction to Civil Engineering
PM Core	6	Select from ENGG1850: Introduction to Project Management
Engineering Core	6	Select from ENGG1111: Integrated Engineering 1
Engineering Core	3	Select from MATH1002: Linear Algebra

Note: ENGG1111 may be replaced by ENGG1061 Advanced Engineering for approved students. MATH1001 and MATH1002 may be replaced by advanced units MATH1901 and MATH1902.

Year 1 - Semester 2

Type	CP	CP From
Engineering Core	3	Select from MATH1003: Integral Calculus and Modelling Note: This unit is discontinued from 2018. Replacement unit is MATH1023.
Civil Core	6	Select from ENGG1802: Engineering Mechanics Note: From 2018, this unit is not available to Civil stream students. Replacement unit is CIVL1802.
PM Core	6	Select from PSYC1002: Psychology 1002
Civil Core	6	Select from GEOL1501: Engineering Geology 1
Engineering Core	3	Select from MATH1005: Statistical Thinking with Data

Note: MATH1003 and MATH1005 may be replaced by advanced units MATH1903 and MATH1905.

Students who fail PSYC1002 in 2016, can either take up PSYC1001 in S1 of 2017 or PMGT1852 in S2 2017.

Year 2 - Semester 1

Type	CP	CP From
Civil Core	6	Select from ENGG1801: Engineering Computing
Civil Core	6	Select from CIVL2201: Structural Mechanics
PM Core	6	Select from ENGG2850: Project Cost and Finance Note: Exclusion with CIVL2812, ENGG2850 is to be taken in preference
Civil Core	6	Select from CIVL2110: Materials

Year 2 - Semester 2

Type	CP	CP From
Engineering Core	2	Select from ENGG2111: Integrated Engineering 2
PM Core	6	Select from BUSS1040: Economics for Business Decision Making
Civil Core	6	Select from CIVL2010: Environmental Engineering
Civil Core	6	Select from CIVL1810: Engineering Construction and Surveying
PM Core	6	Select from ENGG2852: Project Based Organisational Behaviour [not offered in 2020] Note: This unit is discontinued from 2019. Replacement unit is PMGT2854.

Note: ENGG2111 may be replaced by ENGG2062 Engineering Project: Business Plan 2 Adv, with Faculty approval.

Year 3 - Semester 1

Type	CP	CP From
PM Elective	6	Select from PMGT3856: Sustainability and Knowledge Management
PM Core	6	Select from ENGG2851: Project Analytics
Civil Core	6	Select from CIVL2700: Transport Systems
Civil Core	6	Select from MATH2061: Linear Mathematics and Vector Calculus

Year 3 - Semester 2

Type	CP	CP From
PM Core	6	Select from ENGG2855: Project Acceptance
Civil Core	6	Select from CIVL2410: Soil Mechanics 1
Civil Core	6	Select from CIVL2611: Introductory Fluid Mechanics
PM Elective	6	Select from Unit Block: PM Elective

Year 4 - Semester 1

Type	CP	CP From
Engineering Core	2	Select from ENGG3111: Integrated Engineering 3
PM Core	6	Select from ENGG3853: Project Risk Management: Tools & Techniques
Civil Core	6	Select from CIVL3205: Concrete Structures 1
Civil Core	6	Select from CIVL3612: Fluid Mechanics
PM Core	6	Select from PMGT3858: Adapting to Project Context

Note: ENGG3111 may be replaced by ENGG3062 Technology Education (Adv), with Faculty approval.

Year 4 - Semester 2

Type	CP	CP From
PM Core	6	Select from ENGG3854: Legal Aspects of Projects
Civil Core	6	Select from CIVL3206: Steel Structures 1
Civil Core	6	Select from CIVL3811: Engineering Design and Construction
PM Core	6	Select from PMGT3855: Project Variance Analysis

Year 5 - Semester 1

Type	CP	CP From
Engineering Core	2	Select from ENGG4111: Integrated Engineering 4
Engineering Core	6	Select from CIVL4022: Thesis A
Civil Core	6	Select from CIVL4903: Civil Engineering Design
Engineering Core	0	Select from ENGG4000: Practical Experience
List	12	Select from Unit Blocks: Civil Specialist - Breadth Civil Specialist - Depth Note: Students may defer 6cp from this block to semester 2.

Note: ENGG4111 may be replaced by ENGG4064/5 Advanced Engineering Design A/B, with Faculty approval.

Year 5 - Semester 2

Type	CP	CP From
PM Elective	6	Select from PMGT3857: International Project Management
List	6	Select from Unit Blocks: Civil Specialist - Breadth Civil Specialist - Depth Note: Students who have done only 6cp of Civil electives in Semester 1 must complete 12cp of these electives here.
Engineering Core	6	Select from CIVL4023: Thesis B

4. Pathways

48cp Majors

Type

CP From

Note: From 2019 onwards, all engineering majors will be converted to the 48 credit point format, and several new majors will be introduced - details can be viewed in the 2019 degree structures.

You can find more information at https://canvas.sydney.edu.au/courses/2806/pages/feit-your-studies-bachelor-of-engineering-majors