Faculty of Engineering

Civil / Project Management (2018)


Note: This course version applies only to students first enrolling in 2018.
WARNING: This course version is currently under review and is subject to change.


1. Overview

Course: Civil / Project Management (2018)
CP Required: 240
Min FT Duration: 5.00 Years
Min PT Duration: N/A
Faculty/School: Faculty of Engineering
Years Offered: 2018, 2017, 2016, 2015

2. Requirements

Summary

In summary the requirements are:

Students must complete 240 credit points as follows:

Engineering (156 credit points):

► 36 credit points of Engineering core units

► 102 credit points of Civil stream core units

► 12 credit points of Civil Specialist depth units

► 6 credit points of Civil Specialist breadth units

Project Management:

► 66 credit points of Project Management core units

► 18 credit points of Project Management elective units

The handbook rules governing this degree are as follows:

(a) For all Bachelor of Engineering combined degrees a candidate must complete 240 credit points and satisfy any additional requirements specified.

(b) Where the requirements specified in the following clauses account for less than the total required credit, candidates must complete additional units of study from the tables relevant to the Bachelor of Engineering as may be necessary to satisfy the requirements of the degree.

To qualify for the award of the combined degree:

Requirements for the Bachelor of Engineering Honours

(a) The units of study that may be taken for the Bachelor of Engineering Honours component of the combined degree are set out in the tables of units of study for the Bachelor of Engineering Honours single degree;

(b) Except where varied by other clauses of these resolutions, all candidates must complete a minimum of 144 credit points comprising:

(i) 36 credit points from the Engineering Core Table, including all required units;

(ii) 108 credit points from the Engineering Stream Core Table pertaining to the specialist stream being undertaken, including all required units;

(c) The Faculty Board may approve, based on appropriate academic justification, a list of approved unit alternatives. These alternatives specify, for particular Engineering stream / combined degree combinations, units within the normal requirements for the Bachelor of Engineering Honours component of the combined degree that can be replaced by specified alternative units that would form part of the normal program for single degree students in that stream.

Requirements for the Bachelor of Project Management

For the Bachelor of Project Management component of a combined degree:

(a) Candidates must complete the core and elective units of study as set out in the Bachelor of Project Management Unit of Study Table.

Advanced units in Maths and Science

Most units of study offered by the Science Faculty on the list of core requirements can be replaced by an equivalent advanced level unit; subject to prerequisite conditions (as required by the Faculty of Science) being met. Students considering doing advanced options should seek advice from their department before enrolling.

Study Abroad

Students undertaking Study Abroad in a particular year of their degree must enrol in the appropriate International Exchange Program units of study as an alternative to a semester`s standard units.

Permission from the relevant Head of School must be sought prior to enrolling in exchange units of study.

Faculty Resolutions

Details of relevant Faculty resolutions are available via the university handbook site at: http://sydney.edu.au/handbooks/

3. Semesters

Year 1 - Semester 1

Type CP CP From
3 Select from MATH1021: Calculus of One Variable
0 Select from ENGP1000: Professional Engagement Program 1


Note: All students must enrol in ENGP1000 in their first semester of enrolment.
3 Select from MATH1002: Linear Algebra
6 Select from ENGG1111: Integrated Engineering 1
6 Select from ENGG1850: Introduction to Project Management
6 Select from CIVL1900: Introduction to Civil Engineering

Note: MATH1021 and MATH1002 may be replaced by advanced units MATH1921 and MATH1902.

Year 1 - Semester 2

Type CP CP From
6 Select from CIVL1802: Statics
3 Select from MATH1023: Multivariable Calculus and Modelling
6 Select from PMGT1852: Facilitation and Stakeholder Engagement
3 Select from MATH1005: Statistics
6 Select from GEOL1501: Engineering Geology 1

Note: MATH1023 and MATH1005 may be replaced by advanced units MATH1923 and MATH1905.

Year 2 - Semester 1

Type CP CP From
6 Select from CIVL2110: Materials
6 Select from ENGG2850: Project Cost and Finance


Note: Exclusion with CIVL2812, ENGG2850 is to be taken in preference
6 Select from CIVL2201: Structural Mechanics
6 Select from ENGG1801: Engineering Computing

Year 2 - Semester 2

Type CP CP From
2 Select from ENGG2111: Integrated Engineering 2
0 Select from ENGP2000: Professional Engagement Program 2


Note: Enrolment in ENGP2000 is reliant on successful completion of ENGP1000. As such, the placement of ENGP2000 in this structure is example only, and actual enrolment in ENGP2000 is dependent on the time taken to complete ENGP1000.
6 Select from CIVL1810: Engineering Construction and Surveying
6 Select from CIVL2010: Environmental Engineering
6 Select from BUSS1040: Economics for Business Decision Making
6 Select from ENGG2852: Project Based Organisational Behaviour


Note: This unit is discontinued from 2019. Replacement unit is PMGT2854.

Year 3 - Semester 1

Type CP CP From
6 Select from MATH2061: Linear Mathematics and Vector Calculus
6 Select from CIVL2700: Transport Systems
6 Select from ENGG2851: Project Analytics
6 Select from PMGT3856: Sustainability & Knowledge Management

Year 3 - Semester 2

Type CP CP From
6 Select from CIVL2611: Introductory Fluid Mechanics
6 Select from CIVL2410: Soil Mechanics
6 Select from ENGG2855: Project Acceptance
6 Select from Unit Block:
PM Elective

Year 4 - Semester 1

Type CP CP From
6 Select from PMGT3858: Adapting to Project Context
6 Select from CIVL3612: Fluid Mechanics
6 Select from CIVL3205: Concrete Structures 1
6 Select from ENGG3853: Project Risk Management: Tools & Techniques
2 Select from ENGG3111: Integrated Engineering 3

Year 4 - Semester 2

Type CP CP From
6 Select from PMGT3855: Project Variance Analysis
6 Select from CIVL3811: Engineering Design and Construction
6 Select from CIVL3206: Steel Structures 1
6 Select from ENGG3854: Legal Aspects of Projects

Year 5 - Semester 1

Type CP CP From
2 Select from ENGG4111: Integrated Engineering 4
List
12 Select from Unit Blocks:
Civil Specialist - Breadth
Civil Specialist - Depth


Note: Students may defer 6cp from this block to semester 2.
6 Select from CIVL4903: Civil Engineering Design
6 Select from CIVL4022: Thesis A
0 Select from ENGP3000: Professional Engagement Program 3


Note: Enrolment in ENGP3000 is reliant on successful completion of ENGP2000. As such, the placement of ENGP3000 in this structure is example only, and actual enrolment in ENGP3000 is dependent on the time taken to complete ENGP2000.

Year 5 - Semester 2

Type CP CP From
List
6 Select from Unit Blocks:
Civil Specialist - Breadth
Civil Specialist - Depth


Note: Students who have done only 6cp of Civil electives in Semester 1 must complete 12cp of these electives here.
6 Select from PMGT3857: International Project Management
6 Select from CIVL4023: Thesis B

4. Pathways

48cp Majors

Type CP CP From

Note: From 2019 onwards, all engineering majors will be converted to the 48 credit point format, and several new majors will be introduced - details can be viewed in the 2019 degree structures.

You can find more information at https://canvas.sydney.edu.au/courses/2806/pages/feit-your-studies-bachelor-of-engineering-majors

Major in Construction Management (24cp)

Type CP CP From
Core
6 CIVL3805: Project Scope, Time and Cost Management
12 Select from CIVL4810: Mgmnt of People, Quality and Risk in PE
CIVL4813: Contracts Formulation and Management
CIVL4814: Project Procurement and Tendering
CIVL4815: Project Formulation

Note: An additional 6 Credit points must be taken from:

A maximum of 6cp from any other CIVL3####, CIVL4#### or CIVL5### unit from the Civil Core Table or the Civil Specialist Table(s)

Major in Environmental Engineering (24cp)

Type CP CP From
Core
6 CIVL3614: Hydrology
12 Select from CIVL5351: Geoenvironmental Engineering
CIVL5668: Fundamentals of Wind Engineering for Design
CIVL5670: Reservoir, Stream and Coastal Engineering
CIVL5999: Advanced Research and Analysis

Note: An additional 6 Credit points must be taken from:

A maximum of 6cp from any other CIVL3####, CIVL4#### or CIVL5### unit from the Civil Core Table or the Civil Specialist Table(s)

Major in Geotechnical Engineering (24cp)

Type CP CP From
Core
6 CIVL3411: Geotechnical Engineering
12 Select from CIVL5351: Geoenvironmental Engineering
CIVL5453: Geotechnical Hazards
CIVL5458: Numerical Methods in Civil Engineering
CIVL5999: Advanced Research and Analysis

Note: An additional 6 Credit points must be taken from:

A maximum of 6cp from any other CIVL3####, CIVL4#### or CIVL5### unit from the Civil Core Table or the Civil Specialist Table(s)

Major in Humanitarian Engineering (24cp)

Type CP CP From
Core
6 ASNS2665: Understanding Southeast Asia


Note: Students may take PMGT3857, EDUF3026, ITLS6007 or HSBH3009 instead of ASNS2665 as part of the Humanitarian Engineering major
Core
6 CIVL3310: Humanitarian Engineering
Core
6 CIVL5320: Engineering for Sustainable Development
Core
6 CIVL5330: Global Engineering Field Work


Note: Students may take SLIC2000 or SLIC3000 instead of CIVL5330 as part of the Humanitarian Engineering major

Major in Structures (24cp)

Type CP CP From
Core
6 CIVL3235: Structural Analysis
12 Select from CIVL5266: Steel Structures - Stability
CIVL5269: Advanced Concrete Structures
CIVL5277: Structural Rehabilitation and Timber Design
CIVL5458: Numerical Methods in Civil Engineering
CIVL5999: Advanced Research and Analysis

Note: An additional 6 Credit points must be taken from:

A maximum of 6cp from any other CIVL3####, CIVL4#### or CIVL5### unit from the Civil Core Table or the Civil Specialist Table(s)

Major in Transport Engineering (24cp)

Type CP CP From
Core
6 CIVL3703: Transport Policy, Planning and Deployment
6 Select from CIVL5701: Transport Networks
6 Select from CIVL5702: Traffic Engineering

Note: An additional 6 Credit points must be taken from:

A maximum of 6cp from any other CIVL3###, CIVL4### or CIVL5### unit from the Civil Core Table or the Civil Specialist Table(s)

5. Unit Blocks

Block 1 - Engineering Core (Min CP: 36,Max CP: 48)

Unit Code Unit Name CP Sessions Offered
AMME4010 Major Industrial Project 24 Semester 1
Semester 2
AMME4111 Thesis A 6 Semester 1
Semester 2
AMME4112 Thesis B 6 Semester 1
Semester 2
CHNG4203 Major Industrial Project 24 Semester 1
Semester 2
CHNG4811 Thesis A 6 Semester 1
Semester 2
CHNG4812 Thesis B 6 Semester 1
Semester 2
CIVL4022 Thesis A 6 Semester 1
Semester 2
CIVL4023 Thesis B 6 Semester 1
Semester 2
ELEC4712 Thesis A 6 Semester 1
Semester 2
ELEC4713 Thesis B 6 Semester 1
Semester 2
ELEC4714 Major Industrial Project 24 Semester 1
Semester 2
ENGG1111 Integrated Engineering 1 6 Semester 1
Semester 2
ENGG2111 Integrated Engineering 2 2 Semester 1
Semester 2
Int February
ENGG3111 Integrated Engineering 3 2 Semester 1
Semester 2
ENGG4111 Integrated Engineering 4 2 Semester 1
Semester 2
ENGP1000 Professional Engagement Program 1 0 Semester 1
Semester 2
ENGP2000 Professional Engagement Program 2 0 Semester 1
Semester 2
ENGP3000 Professional Engagement Program 3 0 Semester 1
Semester 2
MATH1002 Linear Algebra 3 Semester 1
Summer Main
MATH1005 Statistics 3 Semester 2
Summer Main
MATH1021 Calculus of One Variable 3 Semester 1
Semester 2
MATH1023 Multivariable Calculus and Modelling 3 Semester 1
Semester 2
MATH1902 Linear Algebra (Advanced) 3 Semester 1
MATH1905 Statistics (Advanced) 3 Semester 2
MATH1921 Calculus of One Variable (Adv) 3 Semester 1
MATH1923 Multivariable Calculus and Modelling (Adv) 3 Semester 2

Note: Complete a minimum of 36cp including:

- ENGP1000 (0cp), ENGP2000 (0cp) and ENGP3000 (0cp)

- Exactly 12cp of Integrated Engineering units comprising ENGG1111 (6cp), ENGG2111 (2cp), ENGG3111 (2cp) and ENGG4111 (2cp)

- Exactly 12cp of MATH1xxx units: MATH1021 Calculus of One Variable (3cp) AND MATH1002 Linear Algebra (3cp) AND MATH1023 Multivariable Calculus and Modelling (3cp) AND MATH1005 Statistics (3cp)

- A minimum of 12cp of (see note 1) from either AMME4111-4112 Thesis A & B (6cp+6cp) OR CHNG4811-CHNG4812 Thesis A & B (6cp+6cp) OR CIVL4022-4023 Thesis A & B (6cp+6cp) OR ELEC4712-4713 Thesis A & B (6cp+6cp) OR AMME4010 Major Industrial Project (24cp) OR CHNG4203 Major Industrial Project (24cp) OR ELEC4714 Major Industrial Project (24cp)

Note 1. All Thesis A units are mutually prohibited (meaning that only one can be completed), and all Thesis B units have the associated Thesis A unit as a pre-requisite. Students may undertake only the Thesis units relevant to their stream.

Block 2 - Civil Core (Min CP: 102,Max CP: 108)

Unit Code Unit Name CP Sessions Offered
CIVL1802 Statics 6 Semester 2
Int January
CIVL1810 Engineering Construction and Surveying 6 Semester 2
CIVL1900 Introduction to Civil Engineering 6 Semester 1
CIVL2010 Environmental Engineering 6 Semester 2
CIVL2110 Materials 6 Semester 1
CIVL2201 Structural Mechanics 6 Semester 1
CIVL2410 Soil Mechanics 6 Semester 2
CIVL2611 Introductory Fluid Mechanics 6 Semester 2
CIVL2700 Transport Systems 6 Semester 1
CIVL2812 Project Appraisal 6 Semester 2
CIVL3205 Concrete Structures 1 6 Semester 1
CIVL3206 Steel Structures 1 6 Semester 2
CIVL3612 Fluid Mechanics 6 Semester 1
CIVL3811 Engineering Design and Construction 6 Semester 2
CIVL4903 Civil Engineering Design 6 Semester 1
Semester 2
ENGG1801 Engineering Computing 6 Semester 1
Summer Late
GEOL1501 Engineering Geology 1 6 Semester 2
MATH2061 Linear Mathematics and Vector Calculus 6 Semester 1
Summer Main

Block 3 - PM Core (Min CP: 66,Max CP: 66)

Unit Code Unit Name CP Sessions Offered
BUSS1040 Economics for Business Decision Making 6 Semester 1
Semester 2
ENGG1850 Introduction to Project Management 6 Semester 1
ENGG2850 Project Cost and Finance 6 Semester 1
ENGG2851 Project Analytics 6 Semester 1
Summer Main
ENGG2852 Project Based Organisational Behaviour 6 Semester 2
ENGG2855 Project Acceptance 6 Semester 1
Semester 2
ENGG3853 Project Risk Management: Tools & Techniques 6 Semester 1
ENGG3854 Legal Aspects of Projects 6 Semester 1
Semester 2
Summer Main
PMGT1852 Facilitation and Stakeholder Engagement 6 Semester 2
Int June
PMGT3855 Project Variance Analysis 6 Semester 2
PMGT3858 Adapting to Project Context 6 Semester 1

Block 4 - Civil Specialist - Breadth (Min CP: 6,Max CP: 18)

Unit Code Unit Name CP Sessions Offered
CIVL3235 Structural Analysis 6 Semester 2
CIVL3310 Humanitarian Engineering 6 Semester 1
CIVL3411 Geotechnical Engineering 6 Semester 2
CIVL3614 Hydrology 6 Semester 2
CIVL3703 Transport Policy, Planning and Deployment 6 Semester 1
CIVL3805 Project Scope, Time and Cost Management 6 Semester 1

Block 5 - Civil Specialist - Depth (Min CP: 12,Max CP: 36)

Unit Code Unit Name CP Sessions Offered
CIVL4810 Mgmnt of People, Quality and Risk in PE 6 Semester 2
CIVL4813 Contracts Formulation and Management 6 Semester 2
CIVL4814 Project Procurement and Tendering 6 Semester 2
CIVL4815 Project Formulation 6 Semester 1
CIVL5266 Steel Structures - Stability 6 Semester 1
CIVL5269 Advanced Concrete Structures 6 Semester 2
CIVL5277 Structural Rehabilitation and Timber Design 6 Semester 2
CIVL5320 Engineering for Sustainable Development 6 Semester 2
CIVL5330 Global Engineering Field Work 6 Int July
Int December
CIVL5351 Geoenvironmental Engineering 6 Semester 2
CIVL5453 Geotechnical Hazards 6 Semester 2
CIVL5458 Numerical Methods in Civil Engineering 6 Semester 1
CIVL5668 Fundamentals of Wind Engineering for Design 6 Semester 1
CIVL5670 Reservoir, Stream and Coastal Engineering 6 Semester 1
CIVL5701 Transport Networks 6 Semester 2
CIVL5702 Traffic Engineering 6 Semester 1
CIVL5999 Advanced Research and Analysis 6 Semester 1

Block 6 - PM Elective (Min CP: 18,Max CP: 18)

Unit Code Unit Name CP Sessions Offered
PMGT2854 Executing Projects 6 Semester 1
Semester 2
PMGT3856 Sustainability & Knowledge Management 6 Semester 1
PMGT3857 International Project Management 6 Semester 2