Faculty of Engineering

Mechatronic / Science (Health) (2018)


Note: This course version applies only to students first enrolling in 2018.
WARNING: This course version is currently under review and is subject to change.


1. Overview

Course: Mechatronic / Science (Health) (2018)
CP Required: 240
Min FT Duration: 5.00 Years
Min PT Duration: N/A
Faculty/School: Faculty of Engineering
Years Offered: 2022, 2021, 2020, 2019, 2018

2. Requirements

Summary

In summary the requirements are:

Students must complete 240 credit points as follows:

Engineering (144 credit points):

► 36 credit points of Engineering core units (12cp of MATH1* can count towards Science requirements)

► The Professional Engagement Program comprising ENGP1000 (0cp), ENGP2000 (0cp) and ENGP3000 (0cp)

► 108 credit points of Mechatronic Stream core units

► Up to 12 credit points of Mechatronic Specialist elective units

Science:

► 24 credit points of Science degree core units (12cp of MATH1* can count towards Engineering requirements)

► 60 credit points of Health stream units

► 12 credit points of OLE units

► Up to 12 credit points of Science electives

The handbook rules governing this degree are as follows:

To qualify for the award of the combined degree:

(a) For all Bachelor of Engineering combined degrees a candidate must complete 240 credit points and satisfy any additional requirements specified.

(b) Where the requirements specified in the following clauses account for less than the total required credit, candidates must complete additional units of study from the tables relevant to the Bachelor of Engineering as may be necessary to satisfy the requirements of the degree.

Requirements for the Bachelor of Engineering Honours

(a) The units of study that may be taken for the Bachelor of Engineering Honours component of the combined degree are set out in the tables of units of study for the Bachelor of Engineering Honours single degree;

(b) Except where varied by other clauses of these resolutions, all candidates must complete a minimum of 144 credit points comprising:

(i) 36 credit points from the Engineering Core Table, including all required units;

(ii) 108 credit points from the Engineering Stream Core Table pertaining to the specialist stream being undertaken, including all required units;

(c) The Faculty Board may approve, based on appropriate academic justification, a list of approved unit alternatives. These alternatives specify, for particular Engineering stream / combined degree combinations, units within the normal requirements for the Bachelor of Engineering Honours component of the combined degree that can be replaced by specified alternative units that would form part of the normal program for single degree students in that stream.

Requirements for the Bachelor of Science

For the Bachelor of Science component of a combined degree:

(a) The units of study that may be taken are set out in Table A of the Faculty of Science, and Table S and Table O of the Shared Pool for Undergraduate Degrees.

(b) Candidates must complete 96 credit points in the Bachelor of Science including:

(i) any required degree core units as set out in Table A of the Faculty of Science; and

(ii) a major (48 credit points) or a 3-year program with an embedded major from Table A of the Faculty of Science; and

(iii) 12 credit points of units of study in the Open Learning Environment as listed in Table O; and

(iv) where appropriate, additional electives from Table A of the Faculty of Science or Table S;

(v) If enrolled in a stream, complete the requirements for the stream as specified in Table A of the Faculty of Science.

Advanced units in Maths and Science

Most units of study offered by the Science Faculty on the list of core requirements can be replaced by an equivalent advanced level unit; subject to prerequisite conditions (as required by the Faculty of Science) being met. Students considering doing advanced options should seek advice from their department before enrolling.

Study Abroad

Students undertaking Study Abroad in a particular year of their degree must enrol in the appropriate International Exchange Program units of study as an alternative to a semester`s standard units.

Permission from the relevant Head of School must be sought prior to enrolling in exchange units of study.

Faculty Resolutions

Details of relevant Faculty resolutions are available via the university handbook site at: http://sydney.edu.au/handbooks/

3. Semesters

Year 1 - Semester 1

Type CP CP From
3 Select from MATH1021: Calculus of One Variable
6 Select from ENGG1801: Engineering Computing


Note: INFO1110 is an acceptable alternative for combined degree students wishing to major in Computer Science.
6 Select from MTRX1701: Introduction to Mechatronic Engineering
3 Select from MATH1002: Linear Algebra
6 Select from ENGG1111: Integrated Engineering 1
0 Select from ENGP1000: Professional Engagement Program 1


Note: All students must enrol in ENGP1000 in their first semester of enrolment.

New ENGP units will be in place from 2021. You can find more information at https://canvas.sydney.edu.au/courses/2806/pages/professional-engagement-program-pep-2021-changes

Note: MATH1021 and MATH1002 may be replaced by advanced units MATH1921 and MATH1902.

Students in the Space major do not undertake Integrated Engineering units and should substitute a unit from their major.

Year 1 - Semester 2

Type CP CP From
6 Select from MTRX1702: Mechatronics 1
3 Select from MATH1023: Multivariable Calculus and Modelling
6 Select from AMME1362: Introduction to Engineering Materials
6 Select from ENGG1802: Engineering Mechanics
3 Select from MATH1005: Statistical Thinking with Data

Note: MATH1023 and MATH1005 may be replaced by advanced units MATH1923 and MATH1905.

Year 2 - Semester 1

Type CP CP From
6 Select from Unit Block:
Science Units
6 Select from BIOL1006: Life and Evolution
BIOL1007: From Molecules to Ecosystems
BIOL1008: Human Biology
6 Select from HSBH1012: Introduction to Health and Health Care
6 Select from ELEC1103: Fundamentals of Electrical and Electronic Engineering

Year 2 - Semester 2

Type CP CP From
6 Select from HSBH1013: Society and Health
6 Select from Unit Block:
Science Units
6 Select from PSYC1002: Psychology 1002
6 Select from MTRX1705: Introduction to Mechatronic Design
0 Select from ENGP2000: Professional Engagement Program 2


Note: New ENGP units will be in place from 2021. You can find more information at https://canvas.sydney.edu.au/courses/2806/pages/professional-engagement-program-pep-2021-changes

Year 3 - Semester 1

Type CP CP From
6 Select from Unit Block:
Science Units
6 Select from HSBH2007: Research Methods in Health
6 Select from AMME2500: Engineering Dynamics
6 Select from MTRX2700: Mechatronics 2

Year 3 - Semester 2

Type CP CP From
6 Select from HSBH2009: Innovations in eHealth
2 Select from ENGG2111: Integrated Engineering 2
6 Select from AMME2301: Mechanics of Solids
6 Select from ELEC2104: Electronic Devices and Circuits
6 Select from MECH2400: Mechanical Systems Design 1

Note: Students in the Space major do not undertake Integrated Engineering units and should substitute a unit from their major.

Year 4 - Semester 1

Type CP CP From
6 Select from AMME3500: System Dynamics and Control
6 Select from Unit Block:
Health Science Core


Note: 1x 3000-level selective unit
6 Select from ELEC3204: Power Electronics and Applications
2 Select from ENGG3111: Integrated Engineering 3
6 Select from MECH3660: Manufacturing Engineering
0 Select from ENGP3000: Professional Engagement Program 3


Note: New ENGP units will be in place from 2021. You can find more information at https://canvas.sydney.edu.au/courses/2806/pages/professional-engagement-program-pep-2021-changes

Note: Students in the Space major do not undertake Integrated Engineering units and should substitute a unit from their major.

Year 4 - Semester 2

Type CP CP From
6 Select from Unit Block:
Health Science Core


Note: 1x 3000-level selective research unit
6 Select from MECH3460: Mechanical Systems Design 2
6 Select from MTRX3700: Mechatronics 3
6 Select from MTRX3760: Mechatronic Systems Design

Year 5 - Semester 1

Type CP CP From
2 Select from ENGG4111: Integrated Engineering 4
6 Select from Unit Block:
Health Science Core


Note: 1x 3000-level selective interdisciplinary project unit
6 Select from Unit Block:
Health Science Core


Note: 1x 3000-level selective disciplinary project unit
List
6 Select from Unit Blocks:
Mechatronic Specialist Electives
Science Units


Note: As there are 12cp worth of units that can count to either the Engineering or Science requirements of the combined degree, students can choose to select up to 12cp of electives from either Engineering or Science, or a combination of both.

Students must be sure they will complete the requirements of the Science side of the degree if they want to choose any Engineering elective units.
6 Select from AMME4111: Thesis A

Note: Students in the Space major do not undertake Integrated Engineering units and should substitute a unit from their major.

Year 5 - Semester 2

Type CP CP From
6 Select from Unit Block:
Science Units
List
6 Select from Unit Blocks:
Mechatronic Specialist Electives
Science Units


Note: As there are 12cp worth of units that can count to either the Engineering or Science requirements of the combined degree, students can choose to select up to 12cp of electives from either Engineering or Science, or a combination of both.

Students must be sure they will complete the requirements of the Science side of the degree if they want to choose any Engineering elective units.
6 Select from AMME4112: Thesis B

4. Pathways

48cp Majors

Type CP CP From

Note: From 2019 onwards, all engineering majors will be converted to the 48 credit point format, and several new majors will be introduced - details can be viewed in the 2019 degree structures.

You can find more information at https://canvas.sydney.edu.au/courses/2806/pages/feit-your-studies-bachelor-of-engineering-majors

Major in Space Engineering (24cp)

Type CP CP From
Core
6 AERO2705: Space Engineering 1


Note: Alternate for : ENGG1111
Core
6 AERO3760: Space Engineering 2


Note: Alternate for : MECH3460
Core
6 AERO4701: Space Engineering 3


Note: Alternate for : Mechatronic Specialist Electives:Semester 1
6 Select from Unit Block Space Specialist Electives


Note: Alternate for : Mechatronic Specialist Electives

Note: The 24 cp of units of study from the above table are required to be eligible for the Space Engineering major. Entry requirements ATAR or WAM>75% must be met to be enrolled in this major.

5. Unit Blocks

Block 1 - Engineering Core (Min CP: 36,Max CP: 36)

Unit Code Unit Name CP Sessions Offered
AMME4010 Major Industrial Project 24 Semester 1
Semester 2
AMME4111 Thesis A 6 Semester 1
Semester 2
AMME4112 Thesis B 6 Semester 1
Semester 2
CHNG4203 Major Industrial Project 24 Semester 1
Semester 2
CHNG4811 Thesis A 6 Semester 1
Semester 2
CHNG4812 Thesis B 6 Semester 1
Semester 2
CIVL4022 Thesis A 6 Semester 1
Semester 2
CIVL4023 Thesis B 6 Semester 1
Semester 2
ELEC4712 Thesis A 6 Semester 1
Semester 2
ELEC4713 Thesis B 6 Semester 1
Semester 2
ELEC4714 Major Industrial Project 24 Semester 1
Semester 2
ENGG1111 Integrated Engineering 1 6 Semester 1
ENGG2111 Integrated Engineering 2 2 Semester 1
Semester 2
Int February
ENGG3111 Integrated Engineering 3 2 Semester 1
Semester 2
ENGG4111 Integrated Engineering 4 2 Semester 1
ENGP1000 Professional Engagement Program 1 0 Semester 1
Semester 2
ENGP2000 Professional Engagement Program 2 0 Semester 1
Semester 2
ENGP3000 Professional Engagement Program 3 0 Semester 1
Semester 2
MATH1002 Linear Algebra 3 Semester 1
Semester 2
Summer Main
MATH1005 Statistical Thinking with Data 3 Semester 1
Semester 2
Int January
MATH1021 Calculus of One Variable 3 Semester 1
Semester 2
MATH1023 Multivariable Calculus and Modelling 3 Semester 1
Semester 2
MATH1902 Linear Algebra (Advanced) 3 Semester 1
MATH1905 Statistics (Advanced) 3 Semester 2
MATH1921 Calculus of One Variable (Adv) 3 Semester 1
MATH1923 Multivariable Calculus and Modelling (Adv) 3 Semester 2

Note: Complete a minimum of 36cp including:

- ENGP1000 (0cp), ENGP2000 (0cp) and ENGP3000 (0cp)

- Exactly 12cp of Integrated Engineering units comprising ENGG1111 (6cp), ENGG2111 (2cp), ENGG3111 (2cp) and ENGG4111 (2cp)

- Exactly 12cp of MATH1xxx units: MATH1021 Calculus of One Variable (3cp) AND MATH1002 Linear Algebra (3cp) AND MATH1023 Multivariable Calculus and Modelling (3cp) AND MATH1005 Statistics (3cp)

- A minimum of 12cp of (see note 1) from either AMME4111-4112 Thesis A & B (6cp+6cp) OR CHNG4811-CHNG4812 Thesis A & B (6cp+6cp) OR CIVL4022-4023 Thesis A & B (6cp+6cp) OR ELEC4712-4713 Thesis A & B (6cp+6cp) OR AMME4010 Major Industrial Project (24cp) OR CHNG4203 Major Industrial Project (24cp) OR ELEC4714 Major Industrial Project (24cp)

Note 1. All Thesis A units are mutually prohibited (meaning that only one can be completed), and all Thesis B units have the associated Thesis A unit as a pre-requisite. Students may undertake only the Thesis units relevant to their stream.

Block 2 - Mechatronic Stream Core (Min CP: 108,Max CP: 108)

Unit Code Unit Name CP Sessions Offered
AMME1362 Introduction to Engineering Materials 6 Semester 2
AMME2301 Mechanics of Solids 6 Semester 2
AMME2500 Engineering Dynamics 6 Semester 1
AMME3500 System Dynamics and Control 6 Semester 1
ELEC1103 Fundamentals of Electrical and Electronic Engineering 6 Semester 1
ELEC2104 Electronic Devices and Circuits 6 Semester 2
ELEC3204 Power Electronics and Applications 6 Semester 1
ENGG1801 Engineering Computing 6 Semester 1
Int January
ENGG1802 Engineering Mechanics 6 Semester 2
Summer Main
Int January
MECH2400 Mechanical Systems Design 1 6 Semester 1
MECH3460 Mechanical Systems Design 2 6 Semester 2
MECH3660 Manufacturing Engineering 6 Semester 1
MTRX1701 Introduction to Mechatronic Engineering 6 Semester 1
MTRX1702 Mechatronics 1 6 Semester 2
MTRX1705 Introduction to Mechatronic Design 6 Semester 2
MTRX2700 Mechatronics 2 6 Semester 1
MTRX3700 Mechatronics 3 6 Semester 2
MTRX3760 Mechatronic Systems Design 6 Semester 2

Block 3 - Mechatronic Specialist Electives (Max CP: 30)

Unit Code Unit Name CP Sessions Offered
AMME4710 Computer Vision and Image Processing 6 Semester 2
AMME5520 Advanced Control and Optimisation 6 Semester 1
AMME5790 Introduction to Biomechatronics 6 Semester 2
MECH5720 Sensors and Signals 6 Semester 2
MTRX5700 Experimental Robotics 6 Semester 1

Block 4 - Health Science Core (Min CP: 60,Max CP: 60)

Unit Code Unit Name CP Sessions Offered
BIOL1006 Life and Evolution 6 Semester 1
BIOL1007 From Molecules to Ecosystems 6 Semester 2
BIOL1008 Human Biology 6 Semester 1
HSBH1012 Introduction to Health and Health Care 6 Semester 1
HSBH1013 Society and Health 6 Semester 2
HSBH2007 Research Methods in Health 6 Semester 1
HSBH2009 Innovations in eHealth 6 Semester 2
PSYC1002 Psychology 1002 6 Semester 2
Summer Main

Note: Unit list is incomplete as the Health stream is still under development. Refer to Science Handbook for more information.

Block 5 - Science Units (Min CP: 24,Max CP: 96)

Note: For the Bachelor of Science (Health Stream) component, students are required to complete a total of 96 credit points of Science Table A units as listed in the handbook of the Faculty of Science, including 24 credit points of core units, a 60 credit point Health stream and 12 credit points of OLEs. See Faculty handbooks at http://sydney.edu.au/handbooks

Block 6 - Space Specialist Electives (Min CP: 6,Max CP: 6)

Unit Code Unit Name CP Sessions Offered
AERO5700 Space Engineering (Advanced) 6 Semester 1
Semester 2
AMME4710 Computer Vision and Image Processing 6 Semester 2
AMME5520 Advanced Control and Optimisation 6 Semester 1
AMME5790 Introduction to Biomechatronics 6 Semester 2
MECH5720 Sensors and Signals 6 Semester 2
MTRX5700 Experimental Robotics 6 Semester 1

Block 7 - Machine Learning Elective units (Max CP: 6)

Unit Code Unit Name CP Sessions Offered
COMP3308 Introduction to Artificial Intelligence 6 Semester 1
COMP5318 Machine Learning and Data Mining 6 Semester 1
Semester 2

Note: Students may complete 6 credit points of Machine Learning Elective in place of a Specialist Elective unit.